Search Products

This kit includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.

4 allen type screws for the float bowl are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets and a drill bit complete the package.

Kit includes:

• Main jets: 145, 150, 155 and 160
• Pilot jets: 38, 40 and 42
• Merge Racing AP spring
• JD Fuel screw
• #35 leak jet
• EMP and EMR needles

Everything you need to dial in your FCR/DR650 conversion. Enough jetting to cover most modifications or altitudes.

Not for the stock carburetor Fits FCR-MX conversions Only

Genuine Honda replacement air filter.

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.

An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow

Are you a fan of K&N air filters? Here's one built just for the TW200. Top of line filtering to keep that engine healthy for years to come.

• Increased air flow over the stock air filter
• Designed to increase horsepower and throttle response
• Designed to fit inside the factory air box
• Larger surface area over foam filters which offers longer service intervals in dusty conditions
• Four layers of premium cotton gauze provides outstanding filtration
• Washable & re-usable, never wears out
• One filter will last the lifetime of your bike

Here is the O-Ring that fits in the carburetor manifold. This is the manifold that holds the carb up to the cylinder head. The O-Ring mounts between this manifold and the cylinder head. When this O-Ring fails it allows air into your cylinder and makes your Air Fuel ratio too lean which causes the engine to run too hot.

You can add the double D ring loop to any 1" flat webbing system. This simple piece adds a lot of flexibility to any luggage system you are using. Instantly and easily create a mount point or adjustment point on almost anything. Double D Rings can be used as a secondary buckle and works the same way as a helmet strap. However, the double D rings should NOT be used as a primary means of securing luggage.

Available in 6 colors.

CONSTRUCTION FEATURES

• (2) Heavy Duty 1" Metal D Rings
• 1" Flat Nylon Webbing

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs

Precision Motorcycle Racks strongly recommends these side racks be used with their Top Rack because the racks use each other to mount properly. They were never intended to be used by themselves without the rear rack. 
If you are going to mount these side racks without the use of their top rack please select the extra hardware kit option that includes 2 brackets, 2 steel spacers, and an extra hardware kit that is required for proper installation.

These side racks will not play nice with any other brand rear rack, and installation without their top rack will prove to be quite difficult.

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs

The CRF300L side racks are intended to work hand in hand with their ENDURO Series rear rack. 

If you plan on installing the side racks without their rear rack, you will need the spacer kit to fill in the empty space, which we will send to you at no extra cost. Please select the option when you place this in your cart.

Please note that you will need to remove the left side rack to access your lockable factory storage hatch.

CycleRacks are made out of steel tubing, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.

Please select the rack for your specific model as the differences are significant

• Fully welded construction from 16 gauge mild steel
• Powder-coated black textured finish
• Rigid 4 point mounting system (except off-road model rack)
• Hardware and detailed instructions included

CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.

These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.

Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)

  This is for the add -on Top Plate only.

The simplest piece they make, in a 3, 4, 6, 9, 12 or 15 foot length. This is the runner they use on the bag snake and the side bag haulers.

This piece can be added into any luggage hauling scheme you can dream up.

SPECIFICATIONS:

Construction is a simple piece of 1" Nylon webbing with a loop sewn into one end.

They use the 4 foot length in the side bag hauler kits and the 6 foot length in the bag snake kits.

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.

Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Available in 2 colors

Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.

Features:

• Debris and collision protection for the engine 
• Fully welded 4mm thick aluminum plate / black side made of 2.5mm thick aluminum
• Efficient underbody protection of stone-chipping and collision
• Provides protection for the vulnerable oil pan & lower engine cases
• 100% bolt-on, no drilling, cutting, or any other permanent modifications needed
• Ventilated design maximizes air-flow to prevent overheating
• Silver
• Designed & engineered in Germany

What's in the box:

• SW-MOTECH skid plate engine guard
• Mounting hardware 
• Installation instructions

These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.

Works with 7/8" or 1-1/8" bars.

X-Factor guards may require you to cut your lever ends down, or use short levers.

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

• Fit models with a 1 1/8" stem clamp and a 1 1/8" handlebar
• Handlebar clamps can be pivoted to desired fore and aft location to achieve ideal riding position
• Engineered and tested for maximum strength and durability
• CNC-machined from billet 6061-T6 aluminum, then anodized for long-lasting good looks
• 2" center to center rise above stock position

• Lightweight levers are CNC-machined from aluminum
• Stock length; reach to the lever is adjustable to six positions

Sold Individually

Warp 9 Flex Brake Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces.

Adjustable reach allows customization to the rider’s hand size.

Double hinge design allows lever to flex out of the way in most impact situations.

Pushrod or Bearing contact styles for smooth brake modulation.

Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal.

Replacement shift lever with folding tip for use with OEM footpegs.

A quality set of replacement throttle cables.

This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).

This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.

Designed for OFF ROAD USE with the thought in mind that you can ride to your favorite off road spot using a 15 or 16 tooth sprocket and larger than stock rear sprocket. Then quickly change to the 13 tooth and enjoy the ripping torque provided by the huge amount of reduction the 13 tooth offers. Making the XRL much better in the technical stuff. You will really be surprised how much better a big bike like an XRL handles off road with low gearing.

This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.

Changing sprockets for gearing can wear out the lock washer after a few uses. This is an OEM replacement.

Chain sliders undergo performance degradation over time due to the friction experienced by the chain. To maintain optimal functionality, it is recommended to replace worn components with genuine Honda parts.

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

Chain slippers undergo degradation over time due to friction associated with the chain's movement. To maintain optimal operational performance, it is advised to replace worn components with authentic Honda parts.

Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.

Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.

Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.

  All 520 sprockets require a new retainer plate, please add on if purchasing this size.

These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

Complete chain and sprocket replacement packages.

• JT steel sprockets
• EK SR06 O-ring chain

This an OEM replacement nut for your front sprocket.

Many riders choose to convert over from the stock 525 to a 520 chain. Besides being lighter and less expensive, a 520 chain is more readily available as well as having more sprocket size options.

• Steel Sprockets
• EK SRO6 O-Ring Chain (clip type master link)
• Smaller 3 hole retainer

This is a complete drivetrain package. All the parts you need to freshen up the most important part of your motorcycle.

• Polyurethane Drive Cushions
• Ball Bearing Chain Roller
• Sprocket Bolts and Nuts
• Lock Style Rear Axle Nut
• EK SR06 520 O-Ring Chain
• New front and rear 520 sprockets

Planning a motorcycle trip can be hard work. Butler G1 Maps highlight the best paved motorcycle rides in the country so you don’t have to guess which roads are good. Their dedicated team rides and rates every road you see on the water-proof maps, hundreds of thousands of miles so far. Their easy to read rating system clearly indicates the most dramatic and scenic stretches and are accompanied by detailed inset boxes, written descriptions, elevation profiles and whole bunch of useful information to help you plan your journey.

Looking for motorcycle road trip ideas? How about the best dirt roads by state? Each of the Adventure Series maps highlight the best dirt roads, taking you off-road through some of the most spectacular scenery in the United States.

• Highlights The Best Dirt Roads  |  Features off-highway specific information such as terrain iconography and riding permit requirements
• Waterproof / Tear Resistant  |  The road can be tough on your gear. Our maps are designed to withstand abuse.
• Packs Easily  |  This map folds to 4.25” x 9”.
• Detailed Information  |  Includes written descriptions, points of interest, terrain icons, and elevation profiles of the best dirt roads.

Moose Adventure Windscreen

• Made from aircraft-quality Lucite®​ acrylic
• Heavy-duty, optically clearer than the OEM windscreens
• Available in various heights and sizes
• 5" Shorter version reduces buffeting and improves warm-weather comfort
• Made in the U.S.A.

The touring windshield from Parabellum has been designed, developed and tested using all the knowledge and experience of the KLR riders in their own shop. Using the stock mounting points as well as the cowling mounts increases the rigidity of the shield. 

All new fasteners are included. This new design allows you to move your handlebar to different positions and will not interfere with a stand-up position for off-road use.

This shield is constructed of 3/16" military grade cast acrylic that is 17 inches wide at the bottom tapering to 16 inches at the top.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. 13.5 inches tall, 11.5 inches wide at the bottom, and 8.5 inches wide at the top. Made from military aircraft grade cast acrylic.

Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.

• Tread pattern providing high traction on a variety of terrain
• Large tread blocks for improved tread wear and high speed handling
• High impact, Bias ply, casing structure providing a high level of puncture resistance
• Bias belted casing for improved handling & stability
• Rubber compound designed specifically for wet-slick & dry-hard packed terrain
• Picture provided for purpose of viewing treads.

CNC machined oil filler cap with locking clip to keep it in place in the roughest conditions. The cap is pre-drilled and the locking clip is safety wired to the mounting tap with a section of silicon tubing, that will not melt or discolor, over the wire. First class all the way. Available in Silver, Black, Blue or Red.

DRC is one of the leading manufacturers of silicone hose kits for motorcycles.

• Durable silicone radiator hose for dirt bikes
• Available for MX, ED racers and street dirt bikes
• Smooth inner diameter allows for increased coolant flow
• Printed white DRC logo. Available in red or blue colors

Designed to improve the life and durability of your clutch, Barnett's "Dirt Digger" provides better rideability with less slippage compared to stock.

• Carbon fiber friction plates
• Tempered steel drive plates go through a vibratory de-burring process and then are quality checked for flatness to provide optimum performance.
• Heavy duty clutch springs are pre-set, shot-peened, and heat treated for performance and durability.

Heavy-duty springs help prevent clutch slip in high-performance motors.

• Custom wound from chrome-silicon wire
• Preset for long life
• Higher spring seat pressure to resist clutch slip

A high quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.

Changing your countershaft sprocket? Here is the gasket you need for the left hand side case cover of your TW200. This is the same side of the engine as your gear shift lever and chain.

A complete set of gaskets, o-rings and oil seals. Everything you will need when doing a complete engine re-assembly.

All in one package.

• Hot Rods complete +4mm stroker crank assembly
• 94mm big bore cylinder and piston kit
• Complete gasket set with seals
• Includes new crank bearings

We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.

GoldPlug is the gold standard in engine protection.

Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.

10MM Thread for frame drain.

This 'Bling Ring' replaces the two stock preload/lock rings. The ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.

The added needle bearing thrust washer will make preload adjustments much easier. The ring then spins much easier against the spring making adjustments quite a bit easier.

This part can easily be added to the Cogent or Race Tech Shock Shaft Assemblies, even after they are built.

To install the Bling Ring on a shock with a stock shaft it must either be disassembled or have the lower clevis removed.

Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.

OEM spring rate is 6.7kg/mm. We offer stiffer spring rates for riders who wish to carry luggage or just prefer firmer suspension.

Race Tech shock springs require adapter collars which are included with your spring. *Spring color may vary due to specification requirement and availability.

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

A dual-rate fork spring for the early KLR650. These springs start with a .40 kg/mm winding and after approximately 20% of the stroke, stiffen up to .60 kg/mm for the remainder of the travel. A very nice improvement over the stock springs which are .40 kg/mm for the entire travel.

Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. Designed by Rick at Cogent Dynamics on his high-tech suspension dyno, then tested and endorsed by KLR owners all over, these units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the units under the springs and hit the trails.

If you weigh up to 250 pounds, select the .64 spring kit. If you are over 250 or carry lots of luggage, please select the .70 spring kit. Please call if you have any further questions.

All of these kits include DDCs, springs, fork oil and preload spacers.

The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

You can select from various straight rate springs to customize the package to your needs.

Stock Spring Rate for XR650L: 0.44 kg/mm

Fork brace precision machined from aluminum barstock. Drilled and tapped for optional lower fender attachment.

Hard anodized black for corrosion protection. Fits OEM forks. Split design allows for installing in minutes without having to remove the forks.

The complete fork upgrade kit - Straight rate springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

• Complete assembly, ready to install into the shock body
• Has air bleed holes to help remove air from the oil reservoir during installation
• Double-lip oil seal design keeps out dirt and keeps friction low
• Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

Quality replacement parts for servicing your shock.

• Shock seal head and bushing
• Oil and dust seal
• Shock bumper

Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.

Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.

Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material

Triple-lip seal design

Dyno-tested to last 3 to 4 times longer than OEM seals

Directional ribs allow seal to be installed easily

Kits include fork seals and dust wipers

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• G2-R Gold Valves are dual port pistons optimize the loading of shims while improving flow and can be preloaded, freeloaded or restricted
• Complete instructions, Gold Valve pistons, valving charts, valving shims and "Technical Edge Fork Maintenance and Gold Valve Installation" video all included

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims
• Technical Edge Fork Maintenance and Gold Valve Installation video all included

Another great combination package - the FMF Powerbomb header and Powercore 4 Muffler.

The Powerbomb header promotes better flow by allowing a small expansion of the exhaust gasses improving scavenging. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.

The PowerCore4 muffler was developed to increase the horsepower and torque throughout the entire power curve and give you a noticeable power increase that is very usable and beneficial, no matter what your riding style or ability is.

Some of the features of the PowerCore 4 include: space age internal packing for maximum packing life; hi-flo modular end cap; internal shape of core uses hi-flo technology; enhanced sonic evacuation provides for higher flow and increased power and removable spark arrestor.

The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.

• Uses long-life muffler packing for increased packing life
• Forest Service approved spark arrester

Delayed stock from manufacturer, please ask for availability.

• Reduce exhaust sound by one to six decibels
• Options for DG V2 & RST and for the older "O" & "R" Series mufflers
• Easy installation; remove rear end cap and place Quiet Core in front of the spark arrestor
• Smaller diameter inserts are quieter but more restrictive; larger inserts are less restrictive but louder
• 1" Not recommended for RST
• Each size is sold separately

These DP Standard brake pads are our OEM replacement sintered metal compound. Ideal for everyday use, both on and off-road. They provide excellent all-round braking hot or cold, wet or dry. Where applicable a high-tech ceramic heat shield is applied to the rear of each backplate to reduce the heat transfer into the fluid and prevent brake fade. They have one of the lowest wear rates on the market, very low levels of brake dust and no noise and no thermal cycle bedding-in required are also benefits of the DP Standard brake pads.

EBC Double H Sintered pads feature the HH friction rating - the highest in the industry.

Provides maximum brake effect and lasts twice as long as organic pads.

Sintered Pads from EBC are the best pads we have found for the KLR, they provide good performance in all conditions yet still give you long pad life.

These sets include front and rear brake pads.

• Aramid fibers have high strength-to-weight, thermal stability and abrasion resistance to provide advantages over cheaper steel fiber-based products
• Provide excellent stopping power without noise and rotor galling, even on polished rotors
• Fingertip control and strong, predictable brake response

DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry

Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.

Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.

Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.

Set includes pads for both front calipers.

High performance EBC brake pads.

• The "HH" friction rating is the highest in the industry
• Provide maximum brake effect
• Lasts twice as long as organic pads

This is a complete kit that replaces both front and rear brake pads.

Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!

Set includes front and rear brake pads.

SMX Carbon Look Rotor

• Rotor material has higher friction than plain stainless steel for added stopping power
• Rotors measure 320mm
• Come with caliper relocation bracket
• Designed to fit standard hubs

Quality components at a great price.

• Standard Kit: Includes SS braided lines and EBC sintered brake pads.
• Standard Plus Kit: Includes SS braided lines, EBC sintered pads and an EBC Carbon Steel front rotor.
• Super Plus Kit: Includes SS braided lines, EBC sintered pads and EBC carbon steel front and rear rotors.
• Deluxe Kit: Includes SS braided lines, EBC sintered pads and an EBC Premium 320mm SM front rotor kit.
• Super Deluxe Kit: Includes SS braided lines, EBC sintered pads, an EBC Premium 320mm SM front rotor kit and EBC rear rotor.

Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.

Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.

The Clymer shop service and repair manual. It has all the necessary info to do any maintenance or repairs to your XR650L.

These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.

Matte Black, plastic body with smoke lens and 8mm mount bolt.

Specifications

• E-marked.
• Short Stem: 75mm x 15mm

These signals have short rubberized flexible stems and bright mini halogen bulbs.

• Ministalk Marker Light V-Shape - Black/Amber
• Size:  2-5/8"
• Single-filament bulbs
• Sold in pairs

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

This kit is available with either a chrome or black chrome reflector in the headlight.

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turn signals. We also include splice connectors and split tubing, everything you need for this installation.

There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.

Performance CDI for the Yamaha TTR125 increases the rev limit by 1,000 RPM over the stock rev limit.  Easier starting, crisper throttle response.

This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the new unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines.

This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport

Heavy Duty replacement Voltage Regulator. More robust, but lower cost than the factory unit.

• Most compact of lithium motorsports batteries available
• Ultra-lightweight and high-power
• Can hold a charge up to a year provided there are no “parasitic drains” (accessories that draw power when bike is off (i.e. alarms, ECUs, GPS, heated grips, etc)
• Large all-brass terminal design
• Can be installed in any orientation
• Antigravity batteries include a 3 year pro-rated, non-transferable warranty (registration of the battery with the manufacturer is required within 30 days of purchase by the retail customer). All warranties are to go back through Antigravity.
• Small Case format
• 4.375 x 2.37 x 3.75 inches (LxWxH)
• 240 Cranking Amps
• 11 Amp Hours (Pb Eq)/ 5.5Ah (Actual)/ 70.4Wh
• 1.56 lbs

No Toil rim grease is a high viscosity, non petroleum based compound specially engineered to provide the ultimate filter rim to air box seal. 

Designed to withstand temperatures up to 300° F, it remains waterproof and dust-proof, keeping damaging dust and water from being drawn past your filter

• Biodegradable
• Non toxic, Waterproof
• Easy cleaning in seconds with water and No Toil cleaner

• Revolutionary Parafilm™ formula; spray it on and let it dry
• Doesn't fling off
• Sprays on wet, dries to waxy film and seals the lubricant to your chain
• Non-gooey finish keeps dirt, sand and grit from sticking to freshly lubed chains
• Translates into longer chain life and reduced sprocket wear
• 5.5 oz net wt Aerosol

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area. Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

The T700 comfort sport-touring seat provides you with an increased level of comfort and support to aid with those long days on the bike.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

Available as a Foam & Cover Kit with rear cover only or rear foam & cover kit. 

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.  

On this model, they built up the front of the seat, but dished out the rear slightly to level out the angle of the rider platform, and reduce the slope-into-tank feeling of the stock seat.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.

RotoPax are Rotational Molded - the process which produces indisputably superior products.

• Thicker walls and stronger construction
• Bright colors that are less prone to fading
• Extra threads, thicker walls, and sure-seal gasket guarantee no leaks

Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.

This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.

The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.

All the mounting hardware is stainless steel with machined aluminum spacers also included.

If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Does your stock vacuum petcock leak? Won't shut off? We have the solution with this rebuild kit. Includes a new vacuum diaphragm, O-ring, gasket and inner seal.

If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.

This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.

Machined from billet alloy and anodized for good looks.

  Not for stock fuel tanks!

If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.

  These caps fit Acerbis tanks only.