This replacement lens has a clear panel on the bottom to illuminate your license plate.
Allows you to bolt your license plate directly to the rear fender.
Does not fit Australian DR650.
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack
Recommended to use resistor for proper turn signal flash rate.
Specifications
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.
This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.
Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67
No cutting, drilling, or wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Please note that this product is not compatible with the 1987 TW200.
Includes new Suzuki side panels, heat shield, headlight cover, rear fender and your choice of aftermarket off-road or supermoto front fender.
Choice of off-road or supermoto (SM) front fender.
Blue kits come with white side panels.
Left and right stock OEM Suzuki side panels plastic sold as a pair.
Includes one heat shield. Depending on your application and preferences, more than one heat shield may be useful. Extras can be added here.
Genuine Yamaha OEM replacement air-box seals.
Click on image to enlarge
FunnelWeb ProLine Filter Highlights:
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.
Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.
Designed for use with stock engines using either stock or aftermarket exhaust and air filters.
Changing sprockets for gearing can wear out the lock washer after a few uses. This is an OEM replacement.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Currently available in 15 tooth size only, other sizes coming soon.
Quality steel sprockets and EK SROZ2 525 O-Ring chain. Available in gear ratio choices from - 13/42 to 15/46. EK SROZ2 525 chains come in 120 link length and may have to be cut down to fit. They also come with rivet type master links. Clip type links are available below.
13 and 14 Tooth sprockets require a smaller retainer
Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.
All 520 sprockets require a new retainer plate, please add on if purchasing this size.
High quality steel front sprockets.
These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.
Here is another great upgrade for the TW200 or the VanVan front tire.
Universal 'old school' trials type tread pattern. A versatile performer with a tough nylon carcass and raised dimpled knobs that work well in a variety of terrain.
Tire size is 4.00-18 (64P load / speed rating)
Our Heavy-Duty tubes are made specifically for off-road riding. These are the sturdiest, highest quality tubes on the market. They are 3mm thick with natural rubber construction to better resist pinch flats and are easier to patch than butyl rubber tubes. These have a straight metal valve stem. New tubes deserve new rim strips. Don't forget to add them in to your order.
We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.
But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.
The EVO R series draws on our rich heritage of making power. Offered for various off road MX and sport ATV models, the EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.
By popular demand. This is our own mid-pipe adapter kit for the GSXR exhaust cans. The unique design works with both 3-bolt Hayabusa and 4-bolt GSXR mufflers. It features all stainless steel TIG welded construction with a laser cut adapter. A spring tensioned slip joint allows for heat expansion. A stainless steel hanger strap allows it to attach to your original muffler mounting point. No welding is required. Mid-pipe length is approximately 17" long.
This mid-pipe does not require a stock muffler joint gasket when used with the stock headpipe, the SS Pro-Flow, or the FMF headpipe, eliminating the hump in flow.
Don't forget a fresh seal ring gasket that fits between your muffler and mid-pipe adapter.
The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM).
A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks.
Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap. The installed weight is approximately 7.7 lbs.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
Delayed stock from manufacturer, please ask for availability.
Genuine Honda replacement exhaust gaskets.
Special Feature: Covers linkage. Removable lid for oil filter access (No need to remove skid plate). Compatible with our center stand, version 1 (Slight mod required) & version 2 engine guards (N102EGB2),
Material: Precision CNC machined aircraft grade aluminum
Fit Models: Suzuki
Special feature: Compatible with the T-Rex engine guards (N109-24EG) and center stand (N109-24CS). Removable cover to do oil change. Can be mounted directly on OEM engine guards. Covers linkage
Material: Precision CNC machined aircraft grade aluminum
No Cut or plastic fairing modifications required
Fit Models: Honda
Select these optional heavy duty mounting brackets if you want to replace the wimpy stock mounts with steel brackets.
Their best selling product to protect your bike, Flatland Racing skid plates are made from 5052 3/16" aluminum plate.
They are all hand tig welded together with side engine guards. Installation is easy with our clamps that grip tight.
Their skid plates offer clean out slots and oil plug hole, making oil changes simple. These are more durable than carbon fiber and plastic.
Mounting hardware and instructions included.
Yes, plastic! This is a product from our friends at Acerbis. Ultra tough injection molded reinforced composite. Flexible Heavy-Duty Polypropylene will not effect chassis ability to flex, will not effect handling
It's twice as thick as a metal skid plate but is only half the weight. Plastic glides over rocks and roots better than aluminum. It also reflects less engine noise, bike will run quieter and cooler compared to alloy skid plate. Full coverage, mounts to existing threaded holes at the rear of the frame.
Special Feature: Replaceable black aluminum skid plates. Compatible with our center stand and skid plate
Material: 1" Steel tubing finished in durable black powder coat, aircraft grade aluminum
No cut or plastic fairing modifications required
Fit Models: Suzuki
Special feature: Steel tubes are designed NOT to rotate in a low side and braced together to increase strength
Special feature: Compatible with their skid plate (N109-24SP) and center stand (N109-24CS)
Material: Aircraft grade aluminum, steel tubing (7/8") finished in durable black powder coat
NO CUT or plastic fairing modifications required
Fit Models: Honda
Requires removal of OEM engine guard
Made to match the Yamaha Ténéré 700, these crash bars are made of steel tubing and feature a weather- and corrosion-resistant powder coating in black. The surface finishing is carried out in a state-of-the-art facility in the SW-MOTECH plant in Brno in the Czech Republic.
Crash bars by SW-MOTECH provide the necessary extra safety for tank, fairing and components. Designed specifically for these types of bikes, these accessories fit seamlessly with the lines of the vehicle and offer optimal cornering clearance. Bike-specific mounting systems enable reliable, easy installation onto original attachment points.
These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.
Works with 7/8" or 1-1/8" bars.
X-Factor guards may require you to cut your lever ends down, or use short levers.
It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.
Sold in pairs.
Hand/brush guards are required for proper fitment and for safety reasons.
Hippo Hands go on and off in seconds and never require tools or hardware.
The Backcountry is 9" deep.
If you like to stand and ride, this is the model for you! But… these hand covers also fit to just about any bike. They are also a great option for cruisers with hand guards or lever guards.
They feature a durable, quilted interior and flexible, neoprene cuff which ensures a great fit on so many bikes. The Backcountry is their smallest, most easily adaptable hand cover.
The Backcountry features a front reflective panel for higher visibility in low light situations.
Stored in a nylon pouch with belt attachment
Folding Tool Includes:
SW- Motech manufactured this aluminum brake pedal especially for the Yamaha Ténéré 700.
The adjustable brake pedal made of high-quality milled aluminum with HART-COAT® finish allows for optimized handling and control of the brake. The length of the SW-MOTECH brake pedal can be adjusted by 5 cm, so it suits every foot and every driving style. The tread pattern increases grip and provides improved stability for sporty driving and longer tours. With the Adventure tread (sold separately) you can improve brake pedal handling, especially during offroad driving while standing.
Specially designed shift lever with arm shape suitable for off-road riding, off-road boots, and wide footpegs, and with more space between shift and footpegs.
The revolver system allows for 6 different tip positions including the standard position, which is not available on the stock.
The tip is made of A7079 and is machined with high precision. Knurling on the tip prevents slipping.
Forged A2014 material is used for the arm part, which has high strength and durability.
This listing is for either one throttle cable or one clutch cable, not both.
Brand New External Ignition Coil
Brand new starter relay solenoid switch
Brand new aftermarket voltage regulator rectifier
They have even included the opposite connector (main harness side) as these are often melted/corroded/defective and a major cause for repetitive electrical issues.
Brand New External Ignition Coil
The Trail Tech Vapor Speedometer/Tachometer units are custom designed for an exact fit. They feature a bright white backlit LCD display, waterproof connections, and all parts needed for a complete installation. These units accept AC and DC power input, and automatically switch to internal power if external power is removed. Power connectors are included. Permanent solid-state memory guarantees that data is never lost, even without power. Units are available in black.
Trail Tech provides a one year warranty and unlimited free phone and email support.
Unit functions:
A motorcycle rectifier-regulator is a crucial part of the charging system, acting as a charging control device to prevent damage to your battery and electrical system. These OEM-style units are direct replacements, providing the proper fit and the expected performance on your bike
This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport
Keep your motor running right with fresh spark plugs!
NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.
Affordable starters are constructed with longer-life bearings than OEM.
Many OEM starter motors have an unprotected output needle bearing on the outside of the output shaft's seal; moisture can and does enter the output cap of the electric motor and follows the armature shaft to the unprotected output needle bearing, which corrodes the bearing.
Rick's takes the extra step of installing a double-sealed ball bearing, with the output shaft seal on the outside of the bearing in their new aftermarket unit.
This simple application of common-sense engineering does two things: first, the outside bearing is now protected from damaging water entry, and second, the sealed ball bearing is replaceable.
CNC machined oil filler cap with locking clip to keep it in place in the roughest conditions. The cap is pre-drilled and the locking clip is safety wired to the mounting tap with a section of silicon tubing, that will not melt or discolor, over the wire. First class all the way. Available in Silver, Black, Blue or Red.
The complete Thermo Control package - Our in-house designed Thermostat Bypass kit, a set of Custom Silicone Hoses and a Hi-Pressure Radiator Cap. All combined to help your KLR cooling system be at the top of its game. The Thermostat Bypass kit includes a thermostat with a higher temperature rating that will keep the motor more in its happy spot.
The Silicone hoses are stronger than the stock rubber units and will better resist cracking and leaking.
A direct replacement for the stock KLR hoses that tend to crack and leak after a few years.
These silicone hoses are custom made for us. Silicon hoses operate at much higher temperatures and pressures than other rubbers, they don't perish, and they look great!
New starters that are manufactured to meet or exceed OEM specifications. Pull out your old starter, put in this new one and go riding. These units are built to provide a longer life than the OEM unit with these features:
Heavy-Duty clutch springs
Material: Aircraft grade aluminum, steel, steel tubing (7/8")
No cut or plastic fairing modifications required
Fit Models: Honda
Special feature: Clip attachment and CNC cut sleeves for straps
Material: Steel tubing finished in black powder coating
NO CUT or plastic fairings modification required
Fit Models: Suzuki
The Front Rack gives a lot of options for functionality.
CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.
All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF450L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
The CRF300L side racks are intended to work hand in hand with their ENDURO Series rear rack.
If you plan on installing the side racks without their rear rack, you will need the spacer kit to fill in the empty space, which we will send to you at no extra cost. Please select the option when you place this in your cart.
Please note that you will need to remove the left side rack to access your lockable factory storage hatch.
Minor install marks from a test fit. Comes in original packaging with all hardware included. Sold as is.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Does your stock vacuum petcock leak? Won't shut off? We have the solution with this rebuild kit. Includes a new vacuum diaphragm, O-ring, gasket and inner seal.
The complete shock upgrade kit - a shock spring of your choice, Race Tech Gold Valve kit, detailed instructions and a bottle of quality shock oil to complete the job. Everything you need to transform your mushy stock shock into suspension that really works.
Recommended rates:
The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming out, and improved traction and confidence off-road.
8.6 & 9.6 springs require an adapter which is included.
Recommended rates:
*Spring color may vary due to specification requirement and availability.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
This spring is 8.0kg/mm
OEM spring rates are 5.7-7.6kg/mm progressive style.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
OEM spring rate is 6.7kg/mm. We offer stiffer spring rates for riders who wish to carry luggage or just prefer firmer suspension.
Race Tech shock springs require adapter collars which are included with your spring.
Spring color may vary due to specification requirement and availability.
| Shock Spring | Qty 1 |
| Spring Adapter Collar | Qty 2 |
| Spring Adapter Collar 2 | Qty 1 |
8.0 kg/mm is 24% stiffer than stock
Aluminum alloy lowering link. Lowers the rear suspension approximately 1 inch.
Bearings included.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
A dual-rate fork spring for the early KLR650. These springs start with a .40 kg/mm winding and after approximately 20% of the stroke, stiffen up to .60 kg/mm for the remainder of the travel. A very nice improvement over the stock springs which are .40 kg/mm for the entire travel.
Included in this kit are .42 kg/mm fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and two bottles of 5w fork oil.
These footpeg heads are bike model specific and are required to install Puig footpegs to your bike.
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.
The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.
Kit Contents
The RAM-B-238U consists of a B size 1" diameter rubber ball on a 2.43" x 1.31" diamond plate. The plate has two holes 1.912" from center to center, matches the industry standard AMPS hole pattern and will connect to a large variety of RAM mounts and third party cradles.
A complete kit to mount your phone (or other electronic device) to your motorcycle. The universal cradle expands from 2.25" to 3.25" wide and 4.75" to 6.25" tall. The width is adjustable but fixed while the upper portion of the cradle is spring loaded to keep your device secured in the roughest conditions.
Select the mount option that works best for you. The mirror mount is shown in the photo at left and is a flat plate with an 11mm hole on one side and a RAM ball on the other. Simply remove your mirror, place the plate between your mirror and the perch and tighten it down.
The handlebar mount kit allows you to mount to either a 7/8" or 1-1/8" bar. Also includes hardware to mount to the back of a lever perch. See image at bottom middle for kit pieces.
The X-Grip with handlebar mount is best suited for larger phones up to 4.5" wide. The spring loaded X-Grip cradle expands and contracts, allowing for a perfect custom fit. Kit also includes a device tether recommended for outdoor applications.
Looking for motorcycle road trip ideas? How about a Backcountry ride? Each of our backcountry motorcycle maps highlight the official Backcountry Discovery Routes (BDR) taking you off-road through some of the most spectacular scenery in the United States.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.
Quality components at a great price.
SMX Carbon Look Rotor
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
These Rider's Wrenches by Fredette are combination wrenches that have three wrenches in one! A 2-stroke size spark plug wrench - a front axle and a rear axle wrench. Yep, all three in one unit.
Available in the combinations shown that will fit virtually all current dual-sport machines.
These clever tie-down clamps give you an instant anchor point for tie-down straps using your hand grips.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
In order to be prepared for all possible mechanical mishaps along the trail or on any adventure, we are required to carry a certain selection of tools. The OBR ADV Gear Tool Roll will help keep those tools together and stored in an organized fashion easy to be found should one of those mechanical mishaps occur.
Features
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
The Commuter shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but is much more dished out towards the mid-point to distribute rider weight over a greater area. The passenger platform has been built up to help prevent the passenger from sliding into the rider.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 13" (330mm) |
| Height: | Same as OEM |
RotoPax are Rotational Molded - the process which produces indisputably superior products.
Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.
A highly refined blend of aluminum, copper and graphite lubricants. Use during assembly to prevent galling, corrosion and seizing due to weathering or chemicals. Anti-Seize assures easier disassembly. Temperature range: -60°F to 1600°F (-50°C to 870°C). Salt, corrosion and moisture resistant – ideal for marine use. Meets Mil Spec #907E.
