Search Products

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control.

Sold in pairs.

The complete fork upgrade kit - Race Tech springs and emulators. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

Race Tech has developed these fork springs specifically for the heavier weight of the KLR650.

Sold in pairs.

• The .70 springs are 75% stiffer than stock and will be a great choice for most riders
• The .80 springs are 100% stiffer than stock and will be a better choice for heavier riders

Not for 2014-2018 New Edition

Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass.

Straight rate springs will give better control in the rough stuff. Sold in pairs.

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.

• Bushings are dyno-tested to 500,000 strokes with less wear than OEM bushings
• Kit includes two slider bushings and two leg bushings
• Kit includes all copper washers and O-rings
• Kit includes two fork seal snap rings

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

• Complete assembly, ready to install into the shock body
• Has air bleed holes to help remove air from the oil reservoir during installation
• Double-lip oil seal design keeps out dirt and keeps friction low
• Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

Sold individually.

The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads.  The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.

• Made from super tough glass reinforced zytel
• Reflector Dimensions: 5.25" x 3.5" (135mm x 95mm) 
• Overall mirror length: 7" (175mm) (not including arm mount)
• Convex lens meets SAE and CE specifications 
• Mirror mounts to any 10mm perch.

The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression. 

The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters. 

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends

The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.

Original Kawasaki factory replacement levers for your KLX230.

The elegant, open-end design makes these heated grips both stylish and functional. Highly efficient design, delivering warmth faster than traditional heated grips. Five-level temperature controller adjusts the grips accurately to avoid overheating. Specially selected rubber material resists the outdoor environment and provides a secure and comfortable grip. Even at high-temperatures, the grip remains resistant to damage. 

• Removable end caps allow for use as open-ended grips when needed
• For twist throttle applications
• Note: 12-Volt DC applications only.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.

This clamp comes with 1-1/8" handlebar mounts.

Quality replacement rear fender from Maier.

Rear Fender comes with built in tabs designed to be used with Maier USA Side Panels.

• All Maier bodywork is made of tough, vacuum-formed high-gloss polypropylene
• Drilling is required
• Colors are OE color matched

Replacement front fender by Maier that will fit great on your Kawasaki.

Available in 4 colors.

• Increased tank 14L / 3.6 Gallons.
• Impact and abrasion-resistant.
• Ideal for both competition and long and short-distance tourism.
• Designed to maintain a narrow profile to ensure excellent driveability.
• Possibility of fitting cap with Acerbis key.

Included with the Tank:

• Acerbis cap
• Assembly kit

Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.

Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.

IMS Products 'Adventure Tank' for the Yamaha WR250R/X. They call this an Adventure tank because it maximizes your capacity preparing you for those extended trips without the need to stop and fill up. This tank has a 2.75 gallon advantage over the stock fuel tank and it handles it well.

IMS made this tank to replace the stock radiator shrouds and keep the fuel down low for a lower center of gravity, improving the handling and stability of the bike. They also have installed a lift pump to allow the stock fuel pump to stay in the standard position while efficiently utilizing the entire capacity of the tank. It is available in Natural, Black, Blue, Red and White.
*Graphics For This Tank Are No Longer Available*

Wing Tank - Does Not Use OEM/Stock Shrouds

Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for wherever your adventure takes you! This tank is made from POLYETHYLENE CROSSLINK for extra strength and durability.

DOES NOT FIT NEW KLX300 "R" Models

This kit is for those of you looking for a bit more arm room and a better platform for your feet in the TW cockpit. Included are ProCycle Wide Foot Pegs and our oversize bars with 30mm risers.

• ProCycle Wide Pegs are wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 30mm Moose risers that raise the handlebar 30mm.

Kit does not include new throttle tube. If you have 2001 or newer TW200 and would like a new billet aluminum throttle tube, please select the addon box to receive one with your order.

Here's a UNI dual layer foam air filter element to fit our TW200s. Needs to be treated with air filter oil like any other foam filter.

Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage

Features:

• Coarse open-pore foam catches airborn dirt, grime, and sand
• Fine open-pore inner foam acts as second filter to trap the smallest particles while ensuring maximum air passage
• Adhesive withstands repeated cleaning
• Smaller than stock to increase air space and circulation around filter
• exclusively formulated adhesive withstands repeated cleaning. even with harsh solvents or gasoline
• twin air filters are slightly smaller than stock filters to increase air space around the filter and improve circulation

Here is the O-Ring that fits in the carburetor manifold. This is the manifold that holds the carb up to the cylinder head. The O-Ring mounts between this manifold and the cylinder head. When this O-Ring fails it allows air into your cylinder and makes your Air Fuel ratio too lean which causes the engine to run too hot.

• Include top cover gasket, jet needle E-ring and washer, throttle valve seal, pilot air O-ring, fuel joint O-ring, accelerator pump O-ring, needle valve O-ring, needle valve retainer screw, needle valve assembly, float bowl O-ring/gasket, overflow hose, float bowl screws, accelerator pump rod boot
• Genuine Mikuni parts properly replace worn or mistreated components for the TM42 carburetor
• Includes all the parts needed to rebuild TM42 carburetor

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.

Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.

Buy both and save! Includes the Boyesen QuickShot 3 and Sunline Mixture Screw

This cover acts as an "adjustable leak jet" to fine tune the accelerator pump squirt.

Eliminates "4-stroke bog" when used with correct jetting. Allows the use of correct carburetor settings to optimize performance, starting and reliability. Improved low-end performance with much better throttle response. Investment cast and finished to precise tolerances with internal high volume vertical check valve. Fits all motorcycles and ATVs using a Keihin FCR carb. Easy installation instructions (including online video) and template.

Available for stock gearing, 45 tooth rear sprocket

The 50 tooth rear sprocket will give you much lower gearing for off-road use. You will need a longer chain for this rear sprocket, please order the 130 link chain to fit with this larger sprocket, it may need to be shortened to fit correctly.

These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

Individual 14T, 15T or 16T front sprockets.

JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.

Quality steel sprockets and EK SRO6 O-ring chain. We put them together to make a complete, affordable kit. Chain comes with clip type master link.

Genuine Kawasaki Rear Sprocket.  Size 57T

These masterlinks fit the original OEM Suzuki chain. The original chain is marked DID 525 V8. Choose from Clip Type or Rivet Type.
 

High Quality chain. Will need to be cut to fit your sprocket combination.

The Acerbis 2.0 Chain Guide Block easily replaces the entire OEM unit and ensures durability and high resistance to shock and wear from the chain.

Made of PA6, it is made of two parts that allow installation without removing the chain.
100% PA6 construction Weight: 200 grams

Genuine Kawasaki replacement chain guide. This guide mounts to the lower swing arm.

The RS-2 is a potent and versatile design that evolved from the original TRC, engineered to provide increased power and power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core - and it offers the added bonus of outstanding performance in a value-priced package.

• Diamond-shaped Stainless steel sleeve for increased durability.
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• Weight: .39 lbs lighter than stock configuration
• USFS Approved spark arrester included

The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.

You may want to consider a new exhaust gasket that goes between the header and the muffler.

Benchmark’s Folded Recreation Maps were created for outdoor lovers who want the high quality recreation information in our atlases but with the convenience of a traditional folding map. Complete public lands detail and hunting unit boundaries are shown as well as categorized recreation listings.

Limited to stock on hand

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

The Complete Seats come assembled with an aftermarket pan and ready to ride.

"Will not fit the Rally model"

The ProCycle seat was designed for both comfort and function. Our seat is built with a premium grade foam that is denser for those long days in the saddle, and also giving you freedom to move while standing. 

The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding. If you choose the gel cushion option, it helps improve blood flow, prevents pressure points, and makes it easier to ride for longer without getting tired. 

We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.

For the DR650 that has been lowered or converted with supermoto wheels. This stand is 1.5" (40mm) shorter than the stock unit.

Includes a rear shock mount cover plate and plug for lowing the stock shock.

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Shortens up to 1.5" from stock kickstand length
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Extends approx. 0.5" longer than stock and shortens up to 2.5"
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Extends approx. 0.5" longer than stock and shortens up to 3.5"
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Extends approx. 1" longer than stock and shortens up to 2"
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. 
• Material: Steel tubing with black powder coated finish for strength and durability
• 2008 - 2018, 2023+ KLR650 S (Lower 1", Raise 3.5")
• 2021 - 2022 KLR650 (Lower 3.5", Raise 1")

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. 
• Extends approx. 0.5" longer than stock and shortens up to 4.5" for the KLX300
• Extends approx. 3" longer than stock and shortens up to 2" for the KLX300SM
• Material: Steel tubing with black powder coated finish for strength and durability

Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz

Kit Contents:

• Two pivot tension springs
• Two lock nuts
• Two washers
• Six o-rings
• Two split pins
• Pivot Pegz sticker and instruction sheet

2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.

Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating. 
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

For use on Motion Factory Foot Pegs Only

SW-MOTECH has specially built this centerstand for the Honda Transalp XL750.

The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.

• Stands securely when traveling with lots of luggage and during maintenance
• Bike-specific design for easy mounting and high cornering clearance
• Easy to lift up the motorcycle
• Outrigger for optimal leverage
• Best corrosion resistance due to sand blasting and powder coating of the surface
• Made of robust steel

Cat Crap is the #1 voted anti-fog on the market. Lens cleaner and anti-fog in one. Works for all lenses, eyewear, goggles, helmet visors, etc.

We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.

But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.

Shinko 700 Series tire features an aggressive 60% on-road and 40% off-road read pattern for good dirt riding performance, without sacrificing pavement grip. Other features:

• Aggressive tread pattern with drop lug construction
• Heavy-duty 4-ply carcass for durability
• Reinforced side knobs for cornering stability
• DOT approved

The GP-1 Dual Sport Tire from IRC is designed to provide the best possible handling and control for both on and off the pavement. Special knobs penetrate loose surfaces for excellent traction, braking and cornering off the road yet won't wear off as fast as a full knobby when used on the street. Features include:

• Innovative knob design offers excellent off-road bite
• Won't be shredded on the highway like full knobbies
• DOT approved, 4-ply tire 90% on road, 10% offroad
• All GP-1's are Tube type tires and P rated (max speed of 94 mph)

Available for Front 3.00x21 only

We like red high temperature silicone for use as an adhesive. 

It is much stronger and sticks better than the standard stuff.  It is sensor-safe, low odor, non-corrosive, non-flammable, and non-toxic. 

The resistance to temperatures up to 650°F is a bonus. Comes in a 3 oz tube.
 

No Toil rim grease is a high viscosity, non petroleum based compound specially engineered to provide the ultimate filter rim to air box seal. 

Designed to withstand temperatures up to 300° F, it remains waterproof and dust-proof, keeping damaging dust and water from being drawn past your filter

• Biodegradable
• Non toxic, Waterproof
• Easy cleaning in seconds with water and No Toil cleaner

Eliminates the stock speedometer drive for those who have replaced their stock unit with a Vapor or something similar. Light weight billet alloy spacer and a seal to protect your wheel bearings.

Contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Premium quality EBC Rear brake shoes.

• EBC brake shoes are radius ground, and edge trimmed
• Lead out chamfers at lining ends

Sintered Pads from EBC provide great performance in all conditions yet still give you long pad life. Front pads are double H rated for maximum breaking. Rear pads offer maximum durability and excellent braking performance.

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

This Waterproof First Aid Kit is the perfect size for your "Don't leave home without it" list.

Always keep your first aid kit handy and right where you left it. The Waterproof First Aid Kit easily mounts almost anywhere you need it with self-adhesive hook-and-loop mounts. Contents stored in a heavy-duty nylon bag, with waterproof zipper and special coating to ensure your supplies stay dry.

This box moves up the rev limiter allowing higher revs. It also has a hotter advance curve from the OEM box. This allows for a bit crisper throttle response and easier starting. This is a "must have" for modified KLX110's.

• Raises rev-limiter 1200 rpm over the OEM ignition
• Hotter advance curve for better performance
• Direct replacement for the OEM CDI ignition box

This is the Restart-Remote for Antigravity RE-START (RS) Powersport Batteries with jump-starting built-in. You no longer need to access the battery to press its Re-Start button in the event you over-discharged the battery. Simply plug this accessory into your Battery’s Charging Cable to remotely awaken the RE-START Battery! No need to remove the seat or a fairing to get to the Battery.

• Compatible with Antigravity RE-START Powersport Batteries
• Plugs into SAE Tip of your existing battery charging cable
• Comes with protective zipper case
• Remote requires 9v battery (not included)
• Not compatible with Automotive Batteries

Keep yourself COOL with a set of Moto Hoses. Moto Hoses are what you need to handle the heat that your bike is putting out whether you're pushing it to the limit or just stuck in slow city traffic.

Each Kit Contains:

• Color matched carb vent hoses
• Color matched fuel line
• Color matched coolant overflow hose
• Moto Hose is used by Rock River Yamaha and Honda of Troy motocross teams
• Moto Hose for the WR250R/X is available in Blue or White

The Neutral Sending Unit "NSU" on the DR650 can be a problem. The factory screws tend to loosen over time. You really would not want them to get loose in your motor! The permanent solution is to safety wire them. We looked high and low and finally found pre-drilled screws in the correct length and thread pitch. Here we offer a complete kit to take care of those pesky screws.

If you don't do this, you don't have a screw loose, you have TWO screws loose!

Kit Contents:

• 2 drilled stainless steel screws
• Plenty of safety wire
• Wire twisting tool
• New lock tab for the clutch hub
• New clutch cover gasket

Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

B&B Off Roads Honda XR150L bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.

This ultra tough guard is constructed from 1/8" aluminum and is easy to install.

All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included. 

 Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.

To fit straight 22mm (7/8″) handlebar.

• Barbusters strongest handguard EVER!
• Designed for Enduro and Trail bikes.
• Two mounting points secure the full wrap around aluminum design.
• Compact curved profile to protect hands and levers during intense trail and tight bush riding.
• Heat treated aluminum backbone for maximum strength.
• Replaceable, high impact resistant EGO plastic guards included.
• Large range of colors matched to popular motorcycle brands.
• Deflectors available for increased protection (sold separate).
• Easy installation.
• NOTE: Not ideal for bikes with long clutch and brake levers.

• Powder coated black (shot peened look)
• Fully welded construction
• Rigid 4 point mounting system
• Hardware and detailed instructions included

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs

Precision Motorcycle Racks strongly recommends these side racks be used with their Top Rack because the racks use each other to mount properly. They were never intended to be used by themselves without the rear rack. 
If you are going to mount these side racks without the use of their top rack please select the extra hardware kit option that includes 2 brackets, 2 steel spacers, and an extra hardware kit that is required for proper installation.

These side racks will not play nice with any other brand rear rack, and installation without their top rack will prove to be quite difficult.

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use stock mounting positions as well.

This clamp comes with 1-1/8" bar mounts that work perfectly with the tapered handlebars included. Then there is a new set of ProGrip 714 Rally Grips.

• Interchangeable tips to fit 8 sizes of spoke nipples.
• ( 5.6 / 5.8 / 6.0 / 6.2 / 6.4 / 6.6 / 6.8 / 7.0 mm )
• Main shaft is CNC precision machined from 7075A aluminum and designed for optimum grip.
• Tips are made of heat treated steel for strength.

The cush hub (sprocket carrier) bearing leads a tough life. This is especially true if your cush rubbers get old and soft. They can allow the chain to pull the cush hub sideways putting a twisting load on the bearing. If there's any question about the condition of your bearing replace it now with this double sealed bearing and quality seal.

RT Ultra Slick Grease provides maximum lubrication and minimum friction for seals and bushings. Great for engine seals too.

• Special compound for minimum friction and maximum lubrication
• Perfect for fork seals, bushings and O-rings
• Available in 1-fluid ounce jar

Motion Factory Racing patented Flex-Mount Footpeg System provides superior grip and allows your foot to flex forward and back with the movement or your motorcycle.

One of the key features of Flex-Mount Footpegs is their unique flex-mount design. This design allows the footpegs to absorb shocks and vibrations, reducing fatigue and improving overall comfort during long rides. Additionally, the adjustable height and angle options ensure a personalized fit, allowing you to find the perfect riding position for maximum control and stability.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

They put an a90 bushing on all new mount setups so people can get a good feel for their mid range option. The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

Complete mount system includes: 

• 6061 Aluminum ADV Platforms (65mm wide x 107mm length) 
• Stainless steel mounts
• Sleeve bearing (8x10x20mm) included for 8mm OD' footpeg pins. 
• Right and Left spring included. 
• Chromoly steel spindles with reusable thread locker. 14mm wrench. Torque spec 40 ft/lbs 
• A90 (medium flex) rated bushings
• Cleats and stainless steel machine screws. M3x18mm. These can simply be replaced by going to your local hardware store when damaged or worn out. 
• Bushing bolts. 8mm Allen wrench. Torque spec 30 ft/lbs

 They designed their hardware to bend rather than break in a significant impact. A wrench or adjustable wrench will quickly and easily bend the bolt back straight. Please avoid using a hammer. A little leverage from a long-handled wrench or pipe will do the job. The whole system is rebuild-able and serviceable.

They Fit Kawasaki KLX110 and Yamaha TW200 however some of these bikes may need a little modification by yourself, Please check the size carefully before you buy. If you make mods to the footpegs for fitments it will void all warranties and return policies. 

• This high quality SAE to USB-C and USB port adapter features a switched on/off digital voltage display, allowing you to power your devices with either USB or USB-C charger cables
• It comes with a cover for the USB and USB-C ports when not in use, and 2 zip tie slots (zip ties not included) on the back for securely attaching the adapter to your vehicle
• Its size of 3" x 1-1/4" x 3/4" and protective outdoor rating makes it the ideal solution for your vehicle to charge phones or devices producing 5V at 3.1a power
• Easy install to your SAE battery connector cable
• Crafted from durable ABS plastic
• Standard USB port
• Cables and adapters sold separately 

Plug-In connector kit for your CRF. This kit fits Rally and Non-Rally Versions of the Motorcycle. Wires and terminals will come pre-attached with subharness.  

Plugs into the Aux Power connector. 
Harness length is 32" (2.66ft)

This replacement lens has a clear panel on the bottom to illuminate your license plate. 

Allows you to bolt your license plate directly to the rear fender. 

Does not fit Australian DR650.

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a one beer, plug & play installation.

This is the best performing and highest quality headlight they currently offer.

The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive, ie USA).

The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed!

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive. (USA)

Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack

Recommended to use resistor for proper turn signal flash rate.

Specifications

• Comes with mounting hardware.
• Measures 4" long with base and 1" wide at the lights.

The genuine factory shop service and repair manual. This is the reference manual Suzuki dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your DR650.

Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.

Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.

• Even and Accurate Lubrication: Their patented dispenser features exit holes that align with your chain's link plates, ensuring the areas that need it most get it.
• Minimize Over-spray: Keep your motorcycle clean and free of messy chain lube.
• Reduce Waste: No more over-lubing your chain. Their patented dispenser enhances the efficiency of your lubricant use.
• Rotatable Dispenser: Allows you to adjust your hand positioning. Ideal for bike's with chain guards.
• Durable: Constructed from glass-filled nylon, Oinker is strong, durable, and resistant to chemicals.
• Universal Compatibility: Fits any standard can of lubricant.

*For cans with an attached smart straw, you will need to replace it with the included nozzle

What's Included:

• 1 Chain Oiler
• 3 aerosol straws
• 3 replacement nozzle to be used only on cans that have attached straws.

All that you need to repair and inflate your tire on the road or trail.

• Padded nylon zippered carrying case easily stores inside fanny pack or tool compartment
• Everything needed to repair and inflate tire on the road or trail
• 4" inflator hose accepts threaded cartridges only
• Each cartridge produces 8-9 psi
• Made in the USA

Kit includes:

• 1 - large oblong patch
• 2 - medium size patches
• 3 - small patches
• Thumb buffer
• 0.50 oz tube of rubber cement
• 5 - 4" rubber insert strips
• Insertion tool with screwdriver handle
• Reamer/rasp tool with screwdriver handle
• 3 - 16 gram 3/8" threaded CO² cartridges
• CO² 4" inflator hose

CO² cartridges cannot be transported on an aircraft.

This guard is designed to protect your TW200 headlight from rocks, branches, and any road/trail debris kicked up by the vehicle in front of you.  It’s a one piece laser cut steel component with a sleek black powder coat finish.  Mounting hardware is included. 

Note: installation requires drilling two 1/4” holes in your plastic headlight fairing.

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

Honda XR650L rear shock upgrade. The experts at Cogent Dynamics know suspension! A proven performance rear shock for your XR650L for use under the most demanding conditions and on the roughest terrain worldwide.

Damping rates optimized to your specific needs, giving you the best ride comfort, traction and control. Frequency and velocity sensing valving works great over wide ranging conditions. Low internal friction. All CNC machined components for top quality and performance. Compact and rigid design with internal separator piston. Adjustable for spring preload and rebound damping. Fully serviceable shock is designed for the long haul.

 *Spring color may vary due to specification requirement and availability.

Good News: There’s finally a plug & play LED headlight conversion kit for your 2008-2020 WR250R and WR250X!

This kit includes a sealed LED headlight assembly with plug & play electrical connection, adjustable powder coated steel mounting bracket set, and mounting hardware. 

Installation is a five minute, one beer exercise. If you can change a residential light bulb you will have no problem installing this conversion kit. We promise.

Please note that you will need to reuse your OEM upper headlight mounting grommet and two aim adjustment springs.  Or add new ones to freshen up your whole headlight unit.

Low Beam: 2,100 Lumens, 20 Watts
High Beam: 2,800 Lumens, 30 Watts
Operating Voltage: 10V-30V DC
Color Temp: 6,000K
Lifespan: >50,000 hours