Search Products

Kit includes all seals in the TW200 engine (including crank shaft seals) except valve stem seals. These are high-quality seals made in the USA.

High quality aftermarket paper gasket.

Fresh O-rings to ensure your XRL stays oil-tight and leak free. The Valve Cover Kit includes 4 new valve cover O-rings.

Fresh O-rings to ensure your XRL stays oil-tight and leak free. The Oil Change O-Ring kit includes a filter cover O-ring and a filler plug O-ring.

A high quality top end gasket set for the XR650L

Complete set of engine gaskets with oil seals.

Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height.

Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging".

Anti-swell, alloy impregnated heavy-duty, cork-based facings for smooth clutch take-up, and allows engagement modulation, unlike paper clutches which tend to snatch.

Stage 1 - Excellent mid-range and top-end power increase.

Uses stock valve springs and rockers.

• Exhaust Cam Lobe Duration at 1mm 258°
• Exhaust Cam Lobe Lift 8.800mm
• Exhaust Cam Valve Lash 0.200mm
• Intake Cam Lobe Lift 8.800mm
• Intake Cam Valve Lash 0.150mm
• Intake Lobe Duration at 1mm 258°

  Does not incorporate compression release.

Designed to enhance mid-range and top-end power. Manufactured using the highest quality standards. No core required.

Note: This camshaft has been designed to work with the OEM Yamaha piston, or the BBR big bore kit piston, with OEM sized valves. Any other combination of parts will require that you manually check valve to piston clearance.

Piston, Rings, Wrist Pin, Wrist Pin Bearings and Circlips included.

• This is a 2.41mm, oversized piston, so the cylinder will need to be bored.
• Displacement will go up to 675cc.

NOTE: A top end gasket set is required for installation.

The Complete Top End Performance Kit includes:

• 102.4mm Wiseco piston 9:1 compression (up from 8.3:1) with rings, wrist pin and circlips
• Stage 1 camshaft for more power
• Top end gasket set

This kit boosts your displacement from 644cc to 675cc. Your cylinder must be bored to fit the larger piston.

We all love our TWs, but the stock jetting leaves much to be desired! Here is a Jet Kit for your stock TK carburetor to improve your throttle response. Included in the Kit are a wide range of main jets to cover any setup, one Pilot Jet, one Jet Needle, and five Needle Shims. If you have added an exhaust system or ride at higher elevations, this is a great way to tune your TW for your needs.

Quality air cutoff valve replacement kit contains parts necessary for a complete rebuild.

• Direct OEM-style replacement carburetor air cut-off valve set
• Includes diaphragm, spring and O-ring
• Located on the side of the carburetor, the air cut-off valve prevents lean fuel mixture (backfire) when decelerating
• Temporarily closes the pilot jet airway to provide a richer mix as the throttle closes

If you are converting a Keihin FCR-MX 39 to fit on your DR, you need to start here. This 6061 T6 aluminum adapter bonds to the airbox side of the carb so it will easily fit the DR.

  Not for the stock carburetor Fits FCR-MX conversions only.

Repair kit comes with everything you need to get your carb back in shape.

R&D introduces "Flex-Jet", a simple, effective flexible shaft design. Quick adjustments are now within easy reach. Besides easy access, another benefit is the Flex-Jet's ability to hold its setting. Loose fuel screws are now a thing of the past. Kit includes: Flex-Jet (Remote Fuel Screw), bracket, screw, spring, washer, O-ring and instructions.

Not for the stock DR650 carburetor Fits FCR-MX conversions Only.

Top quality brass screw with molded knob for easy adjustments.

Not for the stock DR650 carburetor Fits FCR-MX conversions Only.

Genuine FCR-MX Carburetor Rebuild Kit

Not for the stock BST DR650 carburetor, Fits FCR-MX conversions Only

• Increased air flow over the stock air filter
• Designed to increase horsepower and throttle response
• Designed to fit inside the factory air box
• Larger surface area over foam filters which offers longer service intervals in dusty conditions
• Four layers of premium cotton gauze provides outstanding filtration
• Washable & re-usable, never wears out
• One filter will last the lifetime of your bike

This cover acts as an "adjustable leak jet" to fine tune the accelerator pump squirt.

Eliminates "4-stroke bog" when used with correct jetting. Allows the use of correct carburetor settings to optimize performance, starting and reliability. Improved low-end performance with much better throttle response. Investment cast and finished to precise tolerances with internal high volume vertical check valve. Fits all motorcycles and ATVs using a Keihin FCR carburetor Easy installation instructions (including online video) and template.

Not for the stock DR650 carburetor Fits FCR-MX conversions Only.

If you are looking to swap out your stock CDI box, the Big Gun Rev Box is an affordable alternative to highly-priced OEM replacement boxes. It increases the overall RPM limit over the stock box and advances the timing curve and is a direct plug-in replacement.

You must cut the green wire on the 8-prong plug going into CDI box.

Performance CDI for the Yamaha TTR125 increases the rev limit by 1,000 RPM over the stock rev limit.  Easier starting, crisper throttle response.

This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the new unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines.

Shorai batteries deliver more energy faster, with less weight and with less wear on the battery per start cycle than any other brand or technology available on the market today.

• Up to 80 percent lighter than their lead acid equivalents
• Improved starting performance
• A Battery Management System that protects the battery from over-discharge.
• Does not sulfate while sitting
• Three year warranty

A HIGH output performance stator that replaces the OEM stator in the Honda XR400R and XR650R models.

ElectroSport designed this to have two sets of output windings: one is floated from ground and has two output leads, and the other is grounded on one side. Both windings also have different winding configurations to ensure optimum output.

Built on a modern stator core made of highly magnetically conductive material. They install the highest grade copper wire using their state-of-the-art computer controlled winding machines and they connect high quality lead wires that are both abrasion and heat resistant.

This stator comes with high grade rubber seals and connectors installed and as such is a plug in replacement.

Even if you don't need the extra lighting or charging output you can still use it as a straight replacement for the OEM stator and it is a very cost effective solution that way.

• Separate circuits for lighting and ignition
• Two output circuits (100w & 50w)
• Fits under the stock flywheel with no modification
• Replaces the stock OEM stator

Complete high quality kit to replace the bearings and seals in the swingarm pivot.

Complete high quality kit to replace the bearings and seals in the KLX shock linkage. Includes the lower shock bearing.

Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.

Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.

• Very light weight
• Stronger than stock
• Front end stability improved and rear end tracks straighter
• Lowers bike 1.00" or 1.75"
• Anodized in black

Billet aluminum lowering links. Lowers the rear suspension.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

• Complete assembly, ready to install into the shock body
• Has air bleed holes to help remove air from the oil reservoir during installation
• Double-lip oil seal design keeps out dirt and keeps friction low
• Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims
• Technical Edge Fork Maintenance and Gold Valve Installation video all included

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of stock pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims and "Technical Edge
• Fork Maintenance and Gold Valve Installation" video all included

The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for riders serious about suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

Top suspension performance requires firm bottoming resistance with plushness at the same time. Even the best suspension tuners can only make the stock valving design work so well. The Gold Valve Shock Suspension System is a proven bolt-on shock valving system that improves control, traction, performance and bottoming resistance.

DRZ400 E/S

A pair of Race Tech fork springs to dial in your front suspension to suit your weight.

Fits all DRZ400 models with conventional forks (not for SM)

Recommended spring rates:

An optional add on to your ProCycle Top Rack to relocate your rear turn signals with ease.

All the parts you need to freshen up your rear brake master cylinder. New piston, seals, return spring, boot and snap ring.

All the parts you need to freshen up your front brake caliper. New piston seals, slide pin and boots. Fix that sticky or limp front brake.

All the parts you need to freshen up your rear brake caliper. New piston seals, slide pin and boots. Fix that sticky or limp rear brake.

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions 
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand 
• Race Sintered are designed for racing use only; not for street use

Includes front and rear pads

Sport Carbon pads:  

• Carbon graphite "X" pads blended with Aramid for leisure/sport use
• Low heat generation
• Best for fast, dry riding; not for mud, water, or sand
• Offroad, Semi-sintered metal

Sintered Pads: 

• The perfect brake pads for leisure use
• Offer maximum durability and excellent braking performance
• Constructed of U.S.-made sintered bronze for longest lifetime
• Best for riding in water, mud, dust, or sand

Race Sintered:

• High performance race pad with superb durability similar to that of the sintered pad.
• Higher friction level and fade resistance
• Diamond ground surface finish to speed bed-in
• Comes with new pad pins
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

EBC brake pad set.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

High quality carbon steel brake rotor.

A great option for every day use, or on your spare rear wheel.

• manufactured from unique ebc low carbon hpsr steel
• laser & cnc punched for lightness
• hardened and ground for precision braking
• nickel coated to resist corrosion

Stock size rear brake rotor laser-cut from high-carbon content 410 stainless steel, then lap cross hatched and heat-treated. Each one then has a high-temp paint applied to surfaces like cooling holes and edges for a clean finished look.

Includes a fresh set of brake rotor bolts.

A set of front and rear brake rotor bolts. 

Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination. Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud. 

Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turn signals. We also include splice connectors and split tubing, everything you need for this installation.

There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount. These are designed for a smaller LED type signal with a 8mm mounting stud. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

The V2 Series Slip-On muffler features an aluminum body, TIG welded components, stainless steel inlet tube and a great new look. This Lightweight Slip-On weighs approximately 5.5 lbs.

The DG Performance systems offer increased throttle response, power and torque. Standard sound level is approximately 98 db. Equipped with a US Forestry approved spark arrestor.

The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available.

Constructed from aircraft grade aluminum and high strength stainless steel.

Sound output 96dB. Several pounds lighter than the stock muffler.

No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.

This muffler works on OEM header only!

Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Unit is pounds lighter than stock and gives gains in horsepower and torque throughout the RPM range. All of that in a package handmade in the USA with a 1 Year Limited Manufacturers Warranty.

The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.

The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.

The RS-4 Twin Pipe kit was previously only available as a custom system for Kevin Schwantz.

Yoshimura is offering these incredible "Twice Pipes" which are completely fabricated by hand and TIG welded to perfection. They certainly sit at the high end of what is available for the mighty SM... The pipes have a stainless steel header and "Y" pipe mated to twin carbon fiber or aluminum RS-4 mufflers for incredible looks and performance. The kit also comes with a custom Yoshimura side stand.

• Pentagonal-shaped sleeve
• Front muffler cap functions as a poly resonant chamber which helps reduce noise
• Two-stage stepped baffle
• Carbon fiber end-cap

The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.

Constructed from 304 stainless steel and breathes much better than the stock unit. Handmade in the USA with a 1 Year Limited Manufacturers Warranty.

Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.

All handmade in the USA with a 1 Year Limited Manufacturers Warranty.

This kit provides some much needed protection for both you and your big DR. Handguards and deflectors protect your hands while the skid plate and Case Armor will cover your baby's soft externals.

• Aluminum Handguard Kit in silver for standard 7/8" bars or 1-1/8" oversize bars
• Spacers so you don't have to cut your balls off (your levers that is!)
• Aluminum Skid Plate
• Stainless Steel Case Armor covers for both right and left hand sides
• Plastic Deflectors - Currently only available in SMALL BLACK

• Made from 4mm thick aircraft aluminum
• Oil drain hole for easy access
• All mounting hardware included

Constructed of durable 3mm powder coated aluminum and easily installed utilizing existing mounts, the R&G Bash Plate (center plate) will protect the underside of your motorcycle from damage and debris. Add Case Guards (left and right plates) to your order for complete protection.

• Made from strong and lightweight aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

• Made from strong and lightweight 4mm thick aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

These hand-crafted bash plates from B&B Eng. are constructed from 4mm 5083 aluminium plate. Strong and lightweight, this material has been selected because of its extreme suitability for welding, abrasion and impact resistance. All the necessary stainless clamps and bolts are included. Plate has a polished finish with foam or rubber where required.

Constructed of heavy-duty machined steel, aluminum, and high-density nylon, R&G frame sliders provide maximum protection and high quality fit and finish. R&G "Aero" sliders have an aerodynamic teardrop shape for a more streamlined look than traditional cylindrical slider pucks

R&G "Cotton" Reel Swingarm Spools are oversize paddock stand bobbins that perform double duty as lifting points for hook style paddock stands as well as protection for the swingarm of your motorcycle in the event of crash or drop.

Protect your frame/paint from scuffs and scratches with these great Frame Guards from B&B Engineering  Made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

Developed on the track and brought to the road. R&G engine case covers are made from 4mm polypropylene for strength, durability and looks that compliment your bike. Both sides included.

PSR has a new shark fin rear rotor protector for the big XR and XRL. CNC machined from forged aluminum and then anodized gun metal in color. This unit bolts to the stock caliper bracket.

This is the ultimate radiator guard for the CRF250L. Protects your  radiator from both front and side impacts.

A rear mounting bracket provides that extra support. Constructed from 1/8" aluminum, the kit includes all necessary mounting hardware for a very simple installation.

A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.

A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

High quality steel rear sprockets from 39 to 53 teeth.

Sprocket color may differ depending on size.

Quality steel rear sprockets.

Color may vary based on manufacturer availability, quality will not be compromised.

Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.

This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.

• ProCycle Low Pegs will drop your pegs by 1-3/4" and include wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 1 1/8" Warp 9 clamps that raise the handlebar 1".
• A new billet aluminum throttle tube is included.

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!

Forged aluminum, black anodized arm and Knurled CNC aluminum shift tip.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of handguards to protect them in case of a fall.

• Machined and knurled 6061 billet aluminum. Actual color may vary
• Removable end cap for easy handguard installation
• Works with standard housing

Warp 9 Supermoto wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples.

• 3.5" x 17" front wheel with stock diameter rotor installed
• 4.25" x 17" rear wheel with rotor and 40T sprocket installed
• Other sprocket sizes available upon request

Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Acerbis fuel tanks were designed to provide additional fuel capacity without sacrificing ergonomics, and are the perfect choice for the rider trying to increase the range of their machine. Constructed of impact and abrasion resistant Polyurethane, Acerbis fuel tanks are durable, stylish, and will provide years of service.

* Will not fit 2017 Model

The Pro Fill Air Chuck from the people at Motion Pro is perfect for those tough to reach valve stems with its pivoting angled head. The design gives users extra hand clearance to avoid hot brake rotors or dirty chains. Billet manufactured from aluminum gives it a precise fit and function combined with light weight. It is finished off with a beautiful blue anodizing and then the Motion Pro logo is laser etched on forever. 1/4" NPT female inlet allows use with common air hose couplings and fittings.

A great addition to any tool box!

The set includes a 24mm for the rear and a 19mm for the front. Each 10 inch forged steel tire iron has a hex wrench on one end. The rounded spoon end minimizes pinched tubes and scarred rims.

This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.

• Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
• Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
• Works on all tapered bearing races from 47 mm to 55 mm OD
• Precision machined anodized aluminum cup will not damage seal surface
• Brass bearing washers for easy use and long life
• Hardened steel jaws engage securely on inner bearing lip
• Lifetime limited warranty

The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws are very easy to strip if you are using a regular Phillips screwdriver.

This is a high quality Motion Pro T-handle driver with #1, #2, and #3 JIS bits made from S2 tool steel. There is bit in each end of the driver held in place magnetically. These are 1/4" hex drive heads so you can use all common driver bits as well. The narrow drive head profile easily fits into tight locations. Main shaft is 8.5" long and is chrome plated for protection.

Contour rotors are ultra lightweight OEM replacement rotors made with tough and durable stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that will perform and last.

Front Rotor, Limited stock

Bolt on horsepower! Stage 1: single-cam motor. Excellent midrange and top-end power increase. Uses stock valve springs and rockers.

Fitment Specs: Exhaust Lift: 5.9; Exhaust Duration at 1.00mm: 223°; Intake Lift: 6.8; Intake Duration at 1.00mm: 227°

Double the size of your side stand footprint and half the chances of your XR650L tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount! All hardware provided.