A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.
A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.
Genuine Kawasaki replacement chain guide. This guide mounts to the lower swing arm.
High-quality DID chain and steel sprockets for 2002 & later TTR125s.
The stock sprocket retainer will rub the chain when it is used with 13 and 14 tooth sprockets.
We have our own sprocket retainer laser cut from 13 gauge stainless steel. This retainer works with all 3-hole 13T, 14T, 15T and 16T DR650 countershaft sprockets.
Warp 9 CNC billet machined Oil Filler Cap.
Available in Blue or Black and it includes a new O-ring
To make removal as easy as possible, the center tab takes a 12mm wrench perfectly, or a 1/4" ratchet drive in the center.
On each end of the center tab is a drilled hole should you find it necessary to safety wire your filler cap in place.
Keep yourself COOL with a set of Moto Hoses. Moto Hoses are what you need to handle the heat that your bike is putting out whether you're pushing it to the limit or just stuck in slow city traffic.
Each Kit Contains:
The Neutral Sending Unit "NSU" on the DR650 can be a problem. The factory screws tend to loosen over time. You really would not want them to get loose in your motor! The permanent solution is to safety wire them. We looked high and low and finally found pre-drilled screws in the correct length and thread pitch. Here we offer a complete kit to take care of those pesky screws.
If you don't do this, you don't have a screw loose, you have TWO screws loose!
Kit Contents:
Complete Gasket Set includes all the gaskets necessary to rebuild the entire engine and transmission, including valve seals.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
10MM Thread
Heavy duty springs help prevent clutch slip in high-performance motors.
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Fit Disc Brake Models Only
The Warp 9 "3-Finger" Lever Exclusive to ProCycle. You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
New from Twin Air, a forged aluminum KLR650 folding shift lever with your choice of Black, Blue, or Green tip. These are 3/4" longer than the stock lever which makes for easier shifting while standing, as well as for those with a larger boot size.
Original Kawasaki factory replacement levers for your KLX230.
CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.
This clamp comes with 1-1/8" handlebar mounts.
For mildly tuned machines using the stock airbox, with stock or K&N filter. May also be used with a good aftermarket exhaust system
Stage 1 Kit Intended for motorcycles with a stock engine using the stock airbox, air filter and stock pipe Fully adjustable to allow the use of well-designed aftermarket pipes and stock replacement air filters like K&N Designed to improve throttle response and driveability In most cases power increases of approximately 5% throughout the entire power range can be achieved
This is a new Diaphragm Set for your 1987-2000 TK carburetor. If yours has cracked or ripped, here is a replacement.
If you are converting a Keihin FCR-MX 39 to fit on your DR, you need to start here. This 6061 T6 aluminum adapter bonds to the airbox side of the carb so it will easily fit the DR.
Not for the stock carburetor Fits FCR-MX conversions only.
Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.
Here's a UNI dual layer foam air filter element to fit our TW200s. Needs to be treated with air filter oil like any other foam filter.
Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage
Features:
ProCycle Rev Box increases the rev limit to 10,000 RPM. In addition, this unit offers a re-mapped timing curve which yields a noticeable increase to horsepower and torque over the stock CDI
This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
DDC Tool will not work with this spring series
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
DDC Tool will not work with this spring series
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are required to realize the full benefits of the DDCs. Please call if you have any further questions.
The DDCs are not recommended for use with progressive springs.
The DDC Install/Removal Tool which makes installation that much easier.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are required to realize the full benefits of the DDCs. Please call if you have any further questions.
The DDCs are not recommended for use with progressive springs.
Add the DDC Install/Removal Tool which makes installation much easier.
The Cogent Dynamics DDC valves are the most cost-effective upgrade you can make to your motorcycle’s forks. Unique and the first of its kind, a DDC kit is available to upgrade many motorcycles that are originally equipped with simple damper rod type forks as front suspension.
We do recommend stiffer than stock front springs to bring the full potential of the DDCs out. OEM springs are dual rate 0.45/0.55 kg.
A CNC machined fork brace to stiffen up the notoriously wimpy front end on the DR. Have more confidence in your front end on or off the pavement.
Split design means that installation takes minutes without having to remove the forks. Available in a black anodized finish.
Custom developed by BBR Motorsports for the ultimate upgrade for mini four-strokes. Sized perfectly for fast/aggressive adult mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults.
Progressive springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs.
They will make a big improvement in the front forks while still delivering a smooth ride. Sold in pairs.
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.
T-Rex Racing skid plate for the Suzuki DR650, designed to protect your bike from dirt, mud, and other debris.
Made from precision CNC machined aircraft grade aluminum finished with black powder coating for durability. Rest assured that you are getting the best material commercially available.
Specifically designed to work with T-Rex Racing engine guards, and center stand.
Will not fit properly with oversized head pipes.
Features:
Features:
Protect the underside of your TW!
B&B Off Roads Honda XR150L bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
You can keep your Cycra handguards even if you upgrade your handlebars to a different width.
Replacement mounts that keep your Cycra handguards fresh and tight.
CNC-machined from billet aluminum for the best fit and strength.
Please Note: These handguards do not fit the Yamaha T7
Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.
Select your desired color.
Must add the corresponding size mounts to fit your handlebar.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Please Note: These handguards do not fit the Yamaha T7
Made to match the Honda XL750 Transalp, these crash bars are equipped with a weather- and corrosion-resistant powder coating in black.
Crash bars by SW-MOTECH provide the necessary extra safety for tank, fairing and components. Designed specifically for these types of bikes, these accessories fit seamlessly with the lines of the vehicle and offer optimal cornering clearance. Bike-specific mounting systems enable reliable, easy installation onto original attachment points.
Crash bars by SW-MOTECH provide the necessary extra safety for tank, fairing and components. Designed specifically for these types of bikes, these accessories fit seamlessly with the lines of the vehicle and offer optimal cornering clearance. Bike-specific mounting systems enable reliable, easy installation onto original attachment points.
Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.
SW-Motech makes some of the finest protection equipment available.
Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.
The upper crash bars are constructed of black, powder-coated steel and are mounted as a supplement to the lower crash bar by SW-MOTECH.
The elements developed exclusively for this motorcycle seamlessly fit the look of the vehicle and guarantee easy mounting. The upper crash bars mainly protect the fairing of the motorcycle and give the motorcycle an individual look.
Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.
SW-Motech makes some of the finest protection equipment available. The set-up for the Twin is available in a standard black powder coating or a semi-polished Stainless-Steel tubing. Both sets will protect the vital components of your motorcycle as well as you from damage incurred during a fall, slide or crash. They will preserve the frame, radiator, bodywork and other critical components from touching down with robust tubular steel. The black kit uses 27/21 mm tubing while the Stainless uses straight 22 mm tubing throughout.
Both configurations have a tight fit for great ground clearance and are designed to work seamlessly with other SW-Motech products like their Skid Plate/Engine Guard and SW-Motech Hawk light mounts. Three secure mounting points per side provide the necessary support that make these so strong. There is no drilling, cutting, welding or any other modifications required for mounting but still allows access to the oil filler, tool box and battery. Kit includes all necessary hardware and instructions and an aluminum cover to replace the OEM plastic cover at the lower mounting point on the left side.
This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.
This ultra tough guard is constructed from 1/8" aluminum and is easy to install.
All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included.
The Bag Snake kit works great for rear bags and side bags. When rigged with a side bag the second ring on the ring tensioner creates a secondary buckle so you can loosen the top for access and your bag doesn't fall away from the bike.
When rigged for a rear bag the diagonal section of the strap prevents any slippage over the ends of the bag. For this reason, the Bag Snake is great for smaller rear bags.
Kit Includes:
Increase your fuel and/or water carrying capacity. This mounting plate attaches to the OEM Suzuki rear rack and accepts the standard RotoPax mounting pedestal. The use of pressed-in threaded mounting hardware allows for quick and easy installation of the plate and pedestal. When not needed the RotoPax pedestal can be quickly removed and the tidy JNS mounting plate left in place.
Order alone or with RotoPax Mount and Water or Fuel container. Get everything you need at one time.
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included. 10.5"Wx11.5"L
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.
The little tool bag that Yamaha provides behind the side cover is nice, but adding this Tool Tube to your TW will make it easier to carry some real tools! The ABS pipe is plugged on each end with waterproof expanding plugs. It is held to the frame of your TW with powder-coated steel straps and brackets. It provides a storage space of 3" ID x 10-1/2" long. Includes all hardware required to mount to your TW200.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
If you already have a Tool Tube you can order just the Locking End Cap and lock.
High Quality Replacement Wheel Bearings and Seals for your TTR125 with disc brakes.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
Eliminates the stock speedometer drive for those who have replaced their stock unit with a Vapor or something similar. Light weight billet alloy spacer and a seal to protect your wheel bearings.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
This replacement lens has a clear panel on the bottom to illuminate your license plate.
Allows you to bolt your license plate directly to the rear fender.
Does not fit Australian DR650.
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Choose mechanical or hydraulic brake switches for your dual-sport conversion
10x1.25 thread. Low profile pressure switch for those applications with limited space above the brake banjo bolt. Kit includes a special replacement banjo bolt. Choose 10x1.25 thread pitch for most Japanese models. Choose 10x1.00 thread pitch for European bikes with Brembo brakes or Japanese bikes with Tokiko brakes.
More range at a great price. Choose the 2.7 gallon tank for the KLX250S in Black, Green, Natural or White.
This tank will NOT fit the 2009-2015 models.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for wherever your adventure takes you! This tank is made from POLYETHYLENE CROSSLINK for extra strength and durability.
DOES NOT FIT NEW KLX300 "R" Models
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
SW-MOTECH has specially built this centerstand for the Honda CB500X.
The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.
SW-MOTECH has specially built this centerstand for the Honda Transalp XL750.
The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.
Double the size of your side stand footprint and half the chances of your KLR tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount.
A must have for lowered bikes.
A must have for lowered bikes.
A must have for lowered bikes.
A must have for lowered bikes.
A must have for lowered bikes.
A must have for lowered bikes.
Pegs that are designed for real adventure, providing a level of comfort not seen with other pegs. 2.25" by 3.5" makes for a platform that you can stand on for long periods with no worries. All necessary parts included for a direct bolt-on application.
Available in a beautiful anodized black or clear aluminum for durability and protection from the elements.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
You can also order serrated or spiked cleats separately.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
The new Fastway Evolution AIR footpegs are now the ultimate pegs in the Universe.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
You can also order serrated or spiked cleats separately. See images.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
The new Fastway Evolution AIR foot pegs are now the ultimate pegs in the Universe.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way.
Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
Mounting these pegs to your KLR takes just a bit of work. Please see link to instructions below to see what you will need to do. These instructions apply to the ADV and Evolution AIR Peg as well as the Evolution II pegs listed on the instructions.
This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.
Patented adjustable collars make it easy to run them in the 'standard' or 'low boy' positions on most bikes.
Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.
The new Fastway Evolution AIR foot pegs are now the ultimate pegs in the Universe.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way.
Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
These mounts provide a 1.0″ drop and 1.0″ shift to the rear which lowers your center of gravity and puts you in a better position of control especially when standing.
They are precision fabricated in Oregon. The icing on the cake, they are 0.5 pounds lighter than the factory peg mounts.
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
3.5MM X 20FT
Made from Tough but lightweight 12 Strand SPECTRA / UHMWPE
2200LBS Break Strength
Double Looped Ends
Each Looped end is Covered in a Kevlar Sheath to protect the rope from abrasion
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.
Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.
This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
You may want to consider a new exhaust gasket that goes between the header and the muffler.
Set your bike apart with a custom exhaust look. Withstands direct heat up to 2000°F.
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.
We like red high temperature silicone for use as an adhesive.
It is much stronger and sticks better than the standard stuff. It is sensor-safe, low odor, non-corrosive, non-flammable, and non-toxic.
The resistance to temperatures up to 650°F is a bonus. Comes in a 3 oz tube.
This Waterproof First Aid Kit is the perfect size for your "Don't leave home without it" list.
Always keep your first aid kit handy and right where you left it. The Waterproof First Aid Kit easily mounts almost anywhere you need it with self-adhesive hook-and-loop mounts. Contents stored in a heavy-duty nylon bag, with waterproof zipper and special coating to ensure your supplies stay dry.
| 6 | Fabric Bandages |
| 1 | 2"x3" TEFLA Pad |
| 1 | Knuckle Bandage |
| 1 | 3"x3" Sterile Gauze Pad |
| 3 | Antiseptic Towelettes |
| 5 | Yards Adhesive Tape |
| 2 | Povidone-Iodine Betadine |
| 2 | 4"x4" Non-sterile gauze |
| 1 | single edge razor blade |
| 1 | Sunscreen |
| 1 | Splinter grabber |
| 1 | 2"x3" Moleskin |
| 2 | 2-packs Acetaminophen |
| 1 | Pair latex gloves |
| 5 | Yards conforming gauze |
| 1 | Sting relief pad |
| 1 | Triple Antibiotic |
| 1 | Instructions |
CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use stock mounting positions as well.
This clamp comes with 1-1/8" bar mounts that work perfectly with the tapered handlebars included. Then there is a new set of ProGrip 714 Rally Grips.
The genuine factory shop service and repair manual. This is the reference manual Suzuki dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your DR650.
Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.
*For cans with an attached smart straw, you will need to replace it with the included nozzle
What's Included:
