Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.
Also works with Edge-2 Circuit Board Upgrade.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount. These are designed for a smaller LED type signal with a 8mm mounting stud. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
NOTE: LED's must be installed on a 12 V DC system!
Eliminates the big clunky rear sub-fender. Makes your XT250 look clean and sporty.
Clean up the backside of your TW200 and upgrade to a brighter, safer LED taillight in one go!
The Tidy Taillight Kit includes a durable, high-quality steel mounting bracket that mounts under your rear fending using the existing bolts. The bracket also has slots to mount your license plate.
The included LED taillight helps make your TW more noticeable to other drivers at night, and the super-bright LED brake lights activate more quickly than stock incandescent bulbs when you get on the brakes, giving drivers behind you more reaction time. The taillight unit also features white LEDs on the underside to light up your license plate and keep you legal.
Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.
OEM Fit for CRF450L rear tail light + turn signal connectors.
Pins pre-installed and pre-crimped with wire for easy install.
Set Includes: Connectors for left and right turn signal and tail light.
This kit is specifically for attaching After-Market tail light and turn signals.
Yoshimura has always been synonymous with quality craftsmanship, precision fitment, and impeccable quality. The Fender Eliminator Kits are no exception, and they are sure to give your motorcycle the sleek race look that every rider craves
Features:
Yoshimura has always been synonymous with quality craftsmanship, precision fitment, and impeccable quality. The Fender Eliminator Kits are no exception, and they are sure to give your motorcycle the sleek race look that every rider craves
Features:
Remove the bulky stock number plate holder with our slim design- comes with LED number plate light.
*Please Note: Brake light does not come with necessary/factory connectors. Some cutting, crimping, soldering of wires may be required for connection.
Sharpen Your Yamaha WR250R’s Look with B&B Off Road’s Tail Tidy
Give your Yamaha WR250R (2008-2021) a shot of attitude with B&B Off Road’s premium tail tidy! This innovative replacement ditches the bulky stock fender for a sleek and stylish design that elevates your bike’s aesthetics without compromising functionality.
Clean Lines, Easy Installation:
This tail tidy boasts a streamlined design that sheds unnecessary weight and bulk, instantly transforming your WR250R’s rear end. The straightforward installation utilizes existing mounting points for a hassle-free experience – get ready to hit the road (or trail) in no time.
Choose Your Finish:
Personalise your tail tidy to match your WR250R’s personality. Opt for a gleaming polished finish for a bold statement, or choose the classic black PPA-Gloss for a refined look. The brand new, low-lustre textured black powder coat (PC) offers a stealthy aesthetic for a more aggressive stance.
Unleash Your WR250R’s Potential:
This tail tidy doesn’t just enhance your bike’s visuals. The reduced weight contributes to improved performance, letting your WR250R handle even better. With a cleaner and more streamlined rear end, your adventure awaits in style.
Upgrade your Yamaha WR250R today! Order your B&B Off Road Tail Tidy and experience the perfect blend of functionality and sharp design.
Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
NOTE: LED's must be installed on a 12 V DC system!
Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turn signals. We also include splice connectors and split tubing, everything you need for this installation.
There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination. Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud.
Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
This is a simple three piece kit you can install in minutes that cleans up the stock DR rear-end.
We use the DR250 taillight that fits perfectly into the pocket of the stock taillight on the DR650 fender. It is smaller, looks great and is out of harms way more than the stock unit. It is a total 'plug-n-play' as the wire pigtail plugs right into the DR650 harness just like stock.
Then we use a small LED light to keep you legal and illuminate your license plate, which gets mounted to our custom stainless steel bracket that is powder coated black, eliminating the stock ugly plastic mount.
Kit includes:
These turn signal relocation brackets from Yoshimura provide an easy way to move the stock turn signal lights or install aftermarket turn signals.
Combines with the Yoshimura fender elimination kit
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
A game changer in auxiliary lights. High output, compact and lightweight!
The New Cyclops Aurora 2 inch lights rated at 4000 lumens combined. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!
Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need an LED flasher to do that)
Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.
Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications.
Look at these quality features!
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes:
This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.
These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.
Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.
Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.
An aluminum Light Mount for your bike. Put whatever light you like up front for more light as well as great daytime visibility to other vehicles. Win-win situation. Choose the Single Mount or Double Mount.
B&B Off Roads Auxiliary single light bracket is made from 5mm 5083 structural plate. It was designed to suit a 6 " light bar. Add an auxiliary bracket and LED light to help Improve visibility whilst night riding.
The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.
This is for Mount Only. Sold individually.
10 Watt LED lights sold separately.
A nice place to mount auxiliary lights on your KLX where they will be high and easy to reach for adjustment but still tight to the cowlings. They will not interfere with controls, body work or the fuel tank.
Constructed of 1/8" stainless steel they are intended for LED lamps in the 2" range, but with a slight slotting of the mounting holes, will work great with 3" lights as well. Includes longer bolts to for the upper triple clamp mounts.
Now a lifetime warrantied LED light set at a budget friendly price.
The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.
We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.
These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).
The amber version is a Cree 3 watt emitters (12 watts per light).
This combo beam pattern offers good forward lighting and extremely good conspicuity.
The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.
Specs:
From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.
JNS has come up with another great addition for the little XT250. Auxiliary light mounts that keep the lights up high for great projection, but still good and tight to the bike for protection. These heavy duty 1/8" stainless steel mounts put your lights out of harms way without interfering with controls, body work, or the fuel tank. Includes four longer upper triple clamp bolts. Everything but the lights themselves to light your way through the darkness.
When usefulness and quality matter the Cyclops Auxiliary light kit for the Yamaha T7 comes shining through and leaves the competition in its wake.
The usefulness of having lights that turn direction with the bars can be very beneficial, perfect for those evenings that might have gone a little long and you need to set up camp or pick your way through a tighter section of trail.
Usefulness from having the ability to run daytime running lights and have full control of low beam settings as well as a switch to disable the system leaving only DRLs on. (Dimmer with cutout switch)
Simplicity for those that don't want to add ANY switches to their bikes, you can choose to have the aux lights activated in a reduced power on low beam (50%) and high beam (100%) via the factory high beam switch by choosing the dimmer option with no switch. We don't like extra switches on our already cluttered bars, Do YOU?
Or have the lights on in high beam and off in low beam, with no switches. Option (I do not want dimming or any switch, Aux lights turn on with factory high beam switch)
If choosing the DRL version, DRLs will be on with the key. By choosing a switch you can disable the main auxiliary lights leaving only the DRL ring on during the daylight. Then at night, flip the switch and have full control of your main auxiliary lights activating in conjunction with your bikes high and low beam, this works very well with the ON with high beam OFF in low beam, No switch option.
With this Cyclops kit you can choose what works best for you.
Benefits of a 100% plug and play setup utilizing all factory Yamaha connectors. If using diming, The high beam wire does use a positap, By far the best way to tap into a wire without causing damage, no tools required.
The basic kit uses our tried-and-true Aurora 2-inch diameter, 19 watt (38 for the set) light kit, All CNC machined, polycarbonate lenses and super lightweight. Each light is rated at 2000 lumens (4000 for the set) with a 15-degree optic throwing a light beam nearly 500 ft
You can choose the DRL or non DRL version.
If no dimmer option is chosen the kit will come with a switch to turn the lights on or off, If you chose the dimmer option you can install the lights with No switch, The auxiliary lights will work in conjunction with the factory headlight, Low beam is set at 50%
With the DRL option, you can also choose the cutout switch, this will disable the system, this works well with the DRL, allowing you the ability to turn the main aux lights off and run with only the DRL halo rings.
They offer mounts for the stock low fender or the Camel ADV high fender kit.
Emark certified for your confidence when riding in countries that require this certification.
Look at these quality features!
KIT DETAILS:
This auxiliary light bar is laser-cut from mild steel and powdercoated black for exceptional looks. The holes on each end of the bar are 3/8" and should not be made any larger for strength reasons.
The bar is very easy to install, just remove two plastic "pop" connectors and install the bar with two bolts with clips. All hardware and instructions are included.
Use these brackets to mount your light weight auxillary lights or turn signals. They will bolt directly on to the DR650 lower triple clamp bolts. This makes for a clean 'tucked in' installation. Sold in pairs.
This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank. If your bike needs improved lighting this mount is the best place to start!
– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.
LED auxiliary lights are sold separate.
Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.
The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!
The stock tail light, blinker and license plate bracket is rather large and cumbersome, to put it politely. The B&B Off Road Engineering unit is simple and tidy and gives you a LED tail and brake light unit, a LED license plate light and turn signal mounts as well.
Installation is easy - remove the stock unit and bolt the new unit in the same location. Off with the old and on with the new in minutes. All necessary hardware included.
