Suspension

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

The Cogent Dynamics DDC valves are the most cost-effective upgrade you can make to your motorcycle’s forks. Unique and the first of its kind, a DDC kit is available to upgrade many motorcycles that are originally equipped with simple damper rod type forks as front suspension.

We do recommend stiffer than stock front springs to bring the full potential of the DDCs out. Up to about 200 pounds (rider with gear on) we recommend the .85 kg/mm springs. If you are above 200 pounds (rider with gear on) you should probably go with the 1.0 kg/mm springs.

Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction

Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals

Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action

Lower Stiction, Longer Life! It doesn’t get any better than this!

Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance. 

Kit includes Fork Seals and dust wipers.

 

Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (Velcro) fastening on back side makes installation or removal for cleaning a breeze.

The complete fork upgrade kit - Race Tech springs and emulators. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

Progressive springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs.

They will make a big improvement in the front forks while still delivering a smooth ride. Sold in pairs.

Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.

• The .85 springs are 30% stiffer than stock DL650 springs and 21% stiffer than DL1000 springs, a great choice for most riders.
• The 1.0 springs are 50% stiffer than stock DL650 springs and 42% stiffer than DL1000 springs, a better choice for heavier or aggressive riders, heavy loads, 2-up riding, etc.
• Stock spring rates for comparison: DL650-.65 DL1000-.70

The V-Strom suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for riders serious about suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

Race Tech Cartridge Emulators make damping rod forks perform like well-tuned cartridge forks. Emulators are tunable valves that sit inside your forks on top of the damping rods and are held in place by the fork springs. Simple to install and completely tunable for all conditions and rider preferences.

Billet aluminum lowering links. Lowers the rear suspension.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Adjustable lowering links by PSR lowers the rear suspension from stock height to 4 inches.

Cogent Dynamics has created another winner - the 'World's Edge' shock for the 650 V-Strom the rear end you have wanted for all these years. This unit gives the DL650 excellent control with a firm but comfortable ride, both solo and two-up. This shock is equipped with adjustable damping control so you can customize the action to your preference. Please call for lowering options also if you need them.

The Bling Ring preload adjuster and thrust bearing on the spring make preload changes easy when you fill the bags and add a copilot. Keeping the ride height up can make the difference between a good handling motorcycle and a peg scraping pig. Want to make it easier yet? Add a Hydraulic Preload Adjuster like the stock shock has.

Includes mounting bracket.

  Bikes with ABS require the hydraulic preload adjuster

This adapter set is required to fit an aftermarket spring to the Vstrom shock

• Lighter and stiffer than stock, these high quality straight rate springs are made specifically for the DL line.
• A proper rear spring will give a smoother more controlled ride.
• Available in a multitude of spring rates, one is the perfect fit for your bike and riding style.
• Stock spring is rated at 8.2 kg/mm for the DL650, and DL1000

 Adapters are required for this spring