Luggage

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists and then anodized black.

PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.

Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets for $15.95 and that will be no problem. See bottom image.

Wide Adventure rack for the WR. Precision laser cut from .25" 5052 aluminum then powder coated black with a shot peened look. This rack is 11" x 17.5" and has numerous tie points for straps or bungees to secure a load. It is pre-drilled for a RotopaX mount. Easy installation means it is bolted to the bike in 10 minutes. There is some minor drilling of the plastic to be done. All necessary hardware and complete instructions included.

The B&B Off Road Engineering rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.

DIMENSIONS

Width Flat Surface Approx 18cm

Length Approx 33cm – Total Length Approx 45cm

Please Note- To fit rack, two holes need to be drilled into the rear guard. The position of holes are already marked on genuine Yamaha guard so no template is required.

A small light-duty Dual Sport Rack for the WR. Precision laser cut from 3/16" 5052 aluminum. It is powder coated black with a shot-peened look. This rack is 9" x 10.5" at widest points and has numerous tie points for straps or bungees. It's pre-drilled for a RotopaX mount. Easy installation means it is bolted to the bike in about 10 minutes. There is some minor drilling of the plastic to be done. All necessary hardware and complete instructions included.

This carry rack is solid and durable made from 5052 aluminum and with its sleek design it will not catch on your clothes or nature.

It is an easy install and will allow you to strap your cooler, lunch box, tools, or whatever on the back of your new Yamaha.

Comes complete with all hardware and easy install instructions.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

Cycle Racks Bag Supports can used for many different Cycle Racks and can be used on either the front or rear rack.

When they developed these, they wanted a functional, yet "Easy On- Easy Off application. The pig tail hook goes up, over and underneath the bar of the rack, they can also be used upside down on the rear rack as side boards. To install them, wing them out, slide them in place and then wing them back down. Simply reverse the process to remove them.

Rok-Straps are supplied to secure them in place. They are pre-drilled to accept the pattern of the Roto-Pax Pack Mount (sold separately) so you can carry fuel or attach them to your own bags.

They are sold together in a set of one right support and one left support.

COLOR: Black

CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.

These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.

Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)

  This is for the add -on Top Plate only.