Auxiliary Lights

This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.

The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.

This is for Mount Only. Sold individually.

10 Watt LED lights sold separately.

This auxiliary light bar is laser-cut from mild steel and powdercoated black for exceptional looks. The holes on each end of the bar are 3/8" and should not be made any larger for strength reasons.

The bar is very easy to install, just remove two plastic "pop" connectors and install the bar with two bolts with clips. All hardware and instructions are included.

These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.

Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.

Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.

An aluminum Light Mount for your bike. Put whatever light you like up front for more light as well as great daytime visibility to other vehicles. Win-win situation. Choose the Single Mount or Double Mount.

JNS has come up with another great addition for the little XT250. Auxiliary light mounts that keep the lights up high for great projection, but still good and tight to the bike for protection. These heavy duty 1/8" stainless steel mounts put your lights out of harms way without interfering with controls, body work, or the fuel tank. Includes four longer upper triple clamp bolts. Everything but the lights themselves to light your way through the darkness.

The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).

Features:

• Heavy Duty Design​
• IP69K Rating​
• Flood, Spot / Flood, & Spot Lens Included
• Stainless Steel Bracket & Hardware​
• 5,000k Light Color – Natural Daylight
• Heavy duty black steel left & right mounting brackets to bolt directly to your lower triple clamp.
• Harness with Switch

This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.

When usefulness and quality matter the Cyclops Auxiliary light kit for the Yamaha T7 comes shining through and leaves the competition in its wake.

The usefulness of having lights that turn direction with the bars can be very beneficial, perfect for those evenings that might have gone a little long and you need to set up camp or pick your way through a tighter section of trail.

Usefulness from having the ability to run daytime running lights and have full control of low beam settings as well as a switch to disable the system leaving only DRLs on. (Dimmer with cutout switch)

Simplicity for those that don't want to add ANY switches to their bikes, you can choose to have the aux lights activated in a reduced power on low beam (50%) and high beam (100%) via the factory high beam switch by choosing the dimmer option with no switch. We don't like extra switches on our already cluttered bars, Do YOU?

Or have the lights on in high beam and off in low beam, with no switches. Option (I do not want dimming or any switch, Aux lights turn on with factory high beam switch)

If choosing the DRL version, DRLs will be on with the key. By choosing a switch you can disable the main auxiliary lights leaving only the DRL ring on during the daylight. Then at night, flip the switch and have full control of your main auxiliary lights activating in conjunction with your bikes high and low beam, this works very well with the ON with high beam OFF in low beam, No switch option.

With this Cyclops kit you can choose what works best for you. 

Benefits of a 100% plug and play setup utilizing all factory Yamaha connectors. If using diming, The high beam wire does use a positap, By far the best way to tap into a wire without causing damage, no tools required.

The basic kit uses our tried-and-true Aurora 2-inch diameter, 19 watt (38 for the set) light kit, All CNC machined, polycarbonate lenses and super lightweight. Each light is rated at 2000 lumens (4000 for the set) with a 15-degree optic throwing a light beam nearly 500 ft

You can choose the DRL or non DRL version.

If no dimmer option is chosen the kit will come with a switch to turn the lights on or off, If you chose the dimmer option you can install the lights with No switch, The auxiliary lights will work in conjunction with the factory headlight, Low beam is set at 50%

With the DRL option, you can also choose the cutout switch, this will disable the system, this works well with the DRL, allowing you the ability to turn the main aux lights off and run with only the DRL halo rings.

They offer mounts for the stock low fender or the Camel ADV high fender kit.

 Emark certified for your confidence when riding in countries that require this certification.

Look at these quality features!

• Solid Steel cradle mount. No broken or cracked mounts!
• CNC machined aluminum housings.
• Poly-carbonate lenses, Break-proof!
• 15-degree beam patterns, a great choice for distance and field of view.
• 19 watts each
• 2000 lumens a piece, 4000 lumens for the set.
• 5500K
• Input voltage 9-30VDC
• R113, R10 TUV and Emark certified.
• IP68 Rated
• Warranty....5-year Function warranty (crash damage excluded)

A nice place to mount auxiliary lights on your KLX where they will be high and easy to reach for adjustment but still tight to the cowlings. They will not interfere with controls, body work or the fuel tank.

Constructed of 1/8" stainless steel they are intended for LED lamps in the 2" range, but with a slight slotting of the mounting holes, will work great with 3" lights as well. Includes longer bolts to for the upper triple clamp mounts.

Use these brackets to mount your light weight auxillary lights or turn signals. They will bolt directly on to the DR650 lower triple clamp bolts. This makes for a clean 'tucked in' installation. Sold in pairs.

Now a lifetime warrantied LED light set at a budget friendly price.

The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.

We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.

These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).

The amber version is a Cree 3 watt emitters (12 watts per light).

This combo beam pattern offers good forward lighting and extremely good conspicuity.

The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.

Specs:

• Canbus compatible, full relayed wire harness included
• 5000 plus lumens for the set
• 28 watt draw per white light, 12 watt draw per amber light
• ISO 67... waterproof
• 5600K (white 33% brighter than Amber)
• Life time warrantied
• Sold as a pair

This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank.  If your bike needs improved lighting this mount is the best place to start!

– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.

LED auxiliary lights are sold separate.

Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.

The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!

From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.