Our offices will be closed on Monday, September 1 for the Labor Day holiday. We will be back on Tuesday, September 2 to process your orders and respond to your inquiries.
Levers, Handlebars, Risers, Grips, Mirrors, Cables
Handlebar mounts that replace your stock clamps.
These raise your handlebars 1 inch.
Available in 7/8" for standard handlebars allow installation of your choice of 7/8" off road handlebars.
Handlebar mounts that replace your stock clamps.
These raise your handlebars 1 inch.
Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.
This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.
Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.
Mount these polished billet aluminum spacers under your handlebar clamps to raise your handlebars 1 inch. High quality longer bolts are included.
CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.
This clamp comes with 1-1/8" handlebar mounts.
These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.
These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).
Throttle cable routing on the XR650L gives you very little extra slack for raising the bars or adjusting them towards the rider. We now offer throttle cables that are 3" longer than stock allowing you to customize the bar position to your riding style.
These quality cables are made by Motion Pro.
Ease the pressure on your wrist during those long highway trips.
ProCycle has developed this unique kit to work with your OEM bars and controls. Just flip the thumb lever down to apply enough friction to hold the throttle in place.
Customize the power characteristics of your bike by simply adding an altered ration cam. The Control cam allows smoother more controlled throttle while the Quick cam lets you put the power to the ground quickly.
Throttle Lock Kit Includes:
Protect your thumbs from blisters caused by riding on the inside of your grips.
Sold in Pairs.
This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.
The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. The black anodized knurled aluminum tip is folding and returns via a stainless-steel return spring. Includes the pinch bolt as well.
The tip is replaceable in the event of damage.
Warp 9 Flex Brake Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces.
Adjustable reach allows customization to the rider’s hand size.
Double hinge design allows lever to flex out of the way in most impact situations.
Pushrod or Bearing contact styles for smooth brake modulation.
Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal.
The Warp 9 "3-Finger" Lever Exclusive to ProCycle. You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.
Replacement folding shift lever, stock length made by IMS.
Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.
The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish.
Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.
1" longer than stock
These tips are for the Warp 9 Shift Levers only.
These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.
You can also order just a new pin hardware kit which comes with new pin and clip.
Replacement folding shift lever, stock length made by IMS.
Replaces all 2 bolt style clutch/brake lever mount clamps. Can help save space on short bend handlebars.
The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise.
Zip ties directly to the bar- no hardware required.
Sold individually
Sold individually.
The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads. The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.
The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression.
The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters.
ADV 3.5" Arm Mirror
Kit Includes:
Can't see past your shoulders? These mirror extenders will get your mirrors higher and farther out for a much better view of the road behind you.
The Enduro Kit is a great option for your street legal dirtbike if you fold away your mirrors often. The longer stem helps the reflector fold behind the headlight and gives good visibility when extended.
Their Doubletake Arm 3.5" is perfect for aggressive riders- long enough to see, but small enough to tuck away.
The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression.
The Doubletake Base Kit includes 5 bolts to thread into every application (even reverse thread Yamaha's), without adapters.
Sold individually.
This assembly includes one Doubletake Arm and one Universal Base Kit.
This mounting system will attach to your current Doubletake Mirror. A mount can be used on either side.
To mount 2 mirrors you need to buy 2 kits. Mirror not included
Doubletake 3.5"
Universal Fit. Every ball kit includes 4 bolts to allow fitment to any bike and eliminate unsightly adapters.
Larger size. Their ball is 1.125”, and even that small increase in diameter makes a big difference in rigidity. This means you don’t have to over-tighten the arm to keep it from moving while riding.
Won't Crush. Their aluminum-filled base ball, coated with high-quality nitrile rubber won’t degrade under extended compression. You won’t have to repeatedly adjust your mirrors, because both ends of the system are designed to last.
Won't spin. They include a lock washer that secures the ball in relation to the bike.
Better hold, less effort. The whole system has been engineered together to keep the mirror from moving, except when it has to in an impact.
Radial Ridges. The clamping surface at the base has radial ridges to hold the ball more securely. These ridges prevent the arm from unintentionally rotating relative to the base, but without mechanical interference that could be damaged under impact.
Asymmetrical Clamping. Because the ball diameters are different, the clamp is located off-center toward the mirror. The larger base diameter creates more stiffness at the bottom, and the offset clamp grips the mirror tighter to equalize rigidity.
Easy Adjustment. Their low profile thumb nut is 25% longer to make adjustment easy even wearing gloves.
The Dual Sport Kit is their most versatile, as it works well on the road and off the road. This kit using their Dual Sport mirror is their go-to for dualsport and dirtbikes, offering great visibility with a low profile.
The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression.
The Doubletake Base Kit includes 5 bolts to thread into every application (even reverse thread Yamaha's), without adapters.
Sold individually.
Dual Sport 3.5" Arm Mirror
