Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
In the event of a crash or even just a dropped bike, these heavy-duty crash bars will prevent major damage.
The powder coated 1" steel tubing is bolted to the sub frame of the bike with two attachment points on each side, preventing them from rotating in the event of a low side.
The guards also feature aircraft grade aluminum plates that can be inexpensively replaced without needing to purchase a new set. Think of them as protection for your protection.
They use highest grade commercially available 12.9 (177,000 psi in tensile strength) wherever possible. Rest assured that you are getting the best material commercially available.
Most skid plates will require notching or modification to avoid interference.
Will not fit properly with oversized head pipes.
ProCycle's 14 gauge stainless steel case armor to protect your engine cases. These case guards bond to your clutch cover and stator cover with high-temp silicone (not included). Extremely tough protection from rocks. In a fall your brake pedal or shift lever can crack the engine case - leaving you stranded. Don't let it happen to you.
Frame Guards protect the frame from wear helping to keep your frame looking new. Mounting hardware is included for quick and easy installation.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
This new guard is designed to protect your DR650 or DRZ400 headlight from rocks, branches, and any road/trail debris kicked up by the vehicle in front of you.
It’s a one piece laser cut steel component with a sleek black powder coat finish, that mounts around the plastic headlight cowling (not included). Mounting hardware is included.
Note: installation requires drilling two 1/4” holes in your plastic headlight fairing.
Fits OEM headlight cowling only. Does not fit Maier aftermarket cowling.
This DR650 Oil Filter Guard is CNC machined from solid 6061 aluminum, black anodized, and then custom laser etched with our logo.
It fits over the fragile OEM magnesium cover and provides great impact protection in the event of a tip over. Proudly made in the USA.
T-Rex Racing skid plate for the Suzuki DR650, designed to protect your bike from dirt, mud, and other debris.
Made from precision CNC machined aircraft grade aluminum finished with black powder coating for durability. Rest assured that you are getting the best material commercially available.
Specifically designed to work with T-Rex Racing engine guards, and center stand.
Will not fit properly with oversized head pipes.
New design gives you more protection and uses OEM mounting points for easy installation.
This is one of the toughest skid plates we've got. Manufactured from 3/16" aluminum that is laser cut and CNC formed, all joints are welded on both sides. The rear mounting bolts are fully recessed for protection. A welded block protects the bolt heads from being bashed and rounded from obstructions. Rubber isolators between the plate and the frame at these two bolt locations help to eliminate vibrations and keep noise down. Front mounts clamp around the frame for a solid connection.
The right side of the plate extends up to cover the oil filter and unbolts from the skid plate for easy filter changes. This skid plate has a black textured powder coat finish for great looks and durability. Includes stainless steel hardware.
