Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a fresh set of brake rotor bolts.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
Warp 9 320mm Supermoto front brake rotor kit. Newly updated and stronger.
Adds serious stopping power to the DR. Included is a new rotor floating on a central mounting carrier along with a caliper relocation bracket.
Available add on options include a Galfer braided stainless steel brake line, and 12oz bottle of Bel-Ray DOT4 brake fluid.
Includes a fresh set of brake rotor bolts.
Stock size rear brake rotor laser-cut from high-carbon content 410 stainless steel, then lap cross hatched and heat-treated. Each one then has a high-temp paint applied to surfaces like cooling holes and edges for a clean finished look.
Includes a fresh set of brake rotor bolts.
A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.
The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.
CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.
These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.
Supermoto forged tubeless wheels. These wheels are machined from forged alloy blanks. A 3.5 x 17" front wheel matched to a 4.25 x 17" rear. Hub can be changed out to fit future bikes. Includes brake rotors, sprocket, cush hub and color matched 90 degree valve stems.
For additional color options please call / email for availability.
Comes complete with:
Includes a color matching (to the hub) 90 degree valve stems
Rear hub is Cush drive
All rotors and sprockets bolt patterns are OEM spec.
Tubeless design offers further weight savings and complexity over spoke wheels
Front wheel without rotor is 10lbs 2 oz
Rear wheel Cush drive no rotor or sprocket is 15lbs
Rear wheel direct drive no rotor or sprocket is 14lbs
Add tires to your wheel order and we will mount and balance them at no additional charge.
Warp 9 Supermoto wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples.
The 3.5" x 17" front wheel includes a 320mm brake rotor and caliper relocation bracket.
The 4.25" x 17" rear wheel also comes with a rear brake rotor already mounted.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Rear wheel Includes Sprocket Carrier with 525 40T Sprocket installed that matches selected hub color.
Billet plugs for your left side case.
Includes both the timing mark plug and the crankshaft access plug.
These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
Limited Stock Available.
A CNC machined fork brace to stiffen up the notoriously wimpy front end on the DR. Have more confidence in your front end on or off the pavement.
Split design means that installation takes minutes without having to remove the forks. Available in a black anodized finish.
Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.
Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Black in color.
Handlebar mounts that replace your stock clamps.
These raise your handlebars 1 inch.
Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.
The Warp 9 "3-Finger" Lever Exclusive to ProCycle. You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
Warp 9 CNC billet machined Oil Filler Cap.
Available in Blue or Black and it includes a new O-ring
To make removal as easy as possible, the center tab takes a 12mm wrench perfectly, or a 1/4" ratchet drive in the center.
On each end of the center tab is a drilled hole should you find it necessary to safety wire your filler cap in place.
These tips are for the Warp 9 Shift Levers only.
These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.
You can also order just a new pin hardware kit which comes with new pin and clip.
The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.
A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.
Anodized, Includes spacers already installed.
Stock sprocket bolt pattern to fit any stock compatible sprocket.
These are designed to work with Warp 9 and OEM hubs.
The starter bushing in the DR650 leads a tough life. Exhaust heat and minimal lube from the factory take their toll. Warp 9 has a high quality solution - a billet starter cover with a sealed ball bearing.
