JNS Engineering

These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.

Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.

Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.

This auxiliary light harness is specifically built for the DR650 using the highest quality materials and components. Wire lengths, component locations, and end terminals are all predetermined and assembled for you. No electrical expertise needed! The relay is wired directly to the battery and Posi-Tap connectors are used to tap in to the existing headlight high beam circuit.

This eliminates the need for a separate switch to operate your auxiliary lights. When your high beam is on, your auxiliary lights will be too. Back to low beam and those high-powered beams will be off so you don't bother oncoming vehicles. There's also an in-line fuse holder for safety and peace of mind. A simple one page instruction sheet is included.

Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.

If you are converting a Keihin FCR-MX 39 to fit on your DR, you need to start here. This 6061 T6 aluminum adapter bonds to the airbox side of the carb so it will easily fit the DR.

  Not for the stock carburetor Fits FCR-MX conversions only.

This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.

The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.

All the mounting hardware is stainless steel with machined aluminum spacers also included.

If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.

Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.

  Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.

A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.

Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.

These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.

Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.

Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.

All hardware is included for a quick and easy installation.

This kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

The headlight features two primary sets of LED projectors, a wide low-beam pattern with distinct upper cutoff and a center spotlight high-beam for long range visibility.

The low-beam consumes 20W and remains powered when the 15W high-beam is fired. There is also a daytime running light feature which can be powered for additional glow. The LEDs are rated for 50,000 hours and operate at a 6000K color temperature.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

Non-DOT

This LED headlight from JNS Engineering is DOT approved and an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and mostly plug and play. The DOT kit does not have a daytime running light (parking light) and may require minor trimming on the backside of the fairing. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb. The primary advantage of this kit over the original is the DOT/SAE markings and a wider high beam pattern.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow.  The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.

• Low Beam: 25W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

An Oil Cooler Guard we can get behind. Laser cut from 0.125" thick 5052 aluminum, CNC formed and powdercoated black.

Designed to fit the stock mounting holes perfectly, most riders will have this in place in minutes. Don't get stuck in the middle of nowhere with a punctured oil cooler.

This DR650 Oil Filter Guard is CNC machined from solid 6061 aluminum, black anodized, and then custom laser etched with our logo.

It fits over the fragile OEM magnesium cover and provides great impact protection in the event of a tip over.  Proudly made in the USA. 

Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.

The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.

This is one of the toughest skid plates we've got. Manufactured from 3/16" aluminum that is laser cut and CNC formed, all joints are welded on both sides. The rear mounting bolts are fully recessed for protection. A welded block protects the bolt heads from being bashed and rounded from obstructions. Rubber isolators between the plate and the frame at these two bolt locations help to eliminate vibrations and keep noise down. Front mounts clamp around the frame for a solid connection.

The right side of the plate extends up to cover the oil filter and unbolts from the skid plate for easy filter changes. This skid plate has a black textured powder coat finish for great looks and durability. Includes stainless steel hardware.

Increase your fuel and/or water carrying capacity. This mounting plate attaches to the OEM Suzuki rear rack and accepts the standard RotoPax mounting pedestal. The use of pressed-in threaded mounting hardware allows for quick and easy installation of the plate and pedestal. When not needed the RotoPax pedestal can be quickly removed and the tidy JNS mounting plate left in place.

• 0.125" 5052 Aluminum, Laser cut / CNC formed
• Powder coated black
• Includes stainless mounting hardware

Order alone or with RotoPax Mount and Water or Fuel container. Get everything you need at one time.