JNS Engineering

These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.

Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.

Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.

Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.

The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!

JNS has come up with another great addition for the little XT250. Auxiliary light mounts that keep the lights up high for great projection, but still good and tight to the bike for protection. These heavy duty 1/8" stainless steel mounts put your lights out of harms way without interfering with controls, body work, or the fuel tank. Includes four longer upper triple clamp bolts. Everything but the lights themselves to light your way through the darkness.

From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.

This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank.  If your bike needs improved lighting this mount is the best place to start!

– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.

LED auxiliary lights are sold separate.

A nice place to mount auxiliary lights on your KLX where they will be high and easy to reach for adjustment but still tight to the cowlings. They will not interfere with controls, body work or the fuel tank.

Constructed of 1/8" stainless steel they are intended for LED lamps in the 2" range, but with a slight slotting of the mounting holes, will work great with 3" lights as well. Includes longer bolts to for the upper triple clamp mounts.

This auxiliary light harness is specifically built for the DR650 using the highest quality materials and components. Wire lengths, component locations, and end terminals are all predetermined and assembled for you. No electrical expertise needed! The relay is wired directly to the battery and Posi-Tap connectors are used to tap in to the existing headlight high beam circuit.

This eliminates the need for a separate switch to operate your auxiliary lights. When your high beam is on, your auxiliary lights will be too. Back to low beam and those high-powered beams will be off so you don't bother oncoming vehicles. There's also an in-line fuse holder for safety and peace of mind. A simple one page instruction sheet is included.

This is a plug & play low profile LED light bar kit which includes laser cut stainless steel mounting brackets and high quality wire taps.

IMPORTANT: Must be used in conjunction with LED headlight or bulb that consumes no more than 35W.

  Please note that this product is not compatible with the 1987 TW200.

Heavy-Duty Rear Master Cylinder Guard for any year model of the KLR. Wrap around design protects the precious master cylinder from damage.

Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.

From JNS Engineering, a super solid Rear Master Cylinder Guard for the XT250, WR250R and X. CNC formed and then powdercoated black for lost lasting corrosion protection. Did we mention how good it looks? All hardware provided.

Do you have lowered foot pegs and can’t get your brake pedal adjusted low enough? 

The tip of this heavy duty JNS rear brake lever is 1.0” lower than the factory component and will get you back in the proper range of adjustment.

ONLY FITS 2012-CURRENT KLR650

If you are converting a Keihin FCR-MX 39 to fit on your DR, you need to start here. This 6061 T6 aluminum adapter bonds to the airbox side of the carb so it will easily fit the DR.

  Not for the stock carburetor Fits FCR-MX conversions only.

This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.

The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.

All the mounting hardware is stainless steel with machined aluminum spacers also included.

If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.

Yamaha TW200 heavy duty chain guard.  

Made from 3/16" laser cut steel protects stock to oversized rear sprockets.  

This unique design bolts in the OEM location but rests against the rear axle bearing spacer for massive impact resistance.  

Yamaha XT250 heavy duty chain guard.  

Made from 3/16" laser cut steel protects stock to oversized rear sprockets.  

This unique design bolts in the OEM location but rests against the rear axle bearing spacer for massive impact resistance.  

Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.

  Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.

This heavy duty DRZ400 chain guard is made of laser cut 1/8” aluminum and finished in textured black powder coating.  The formed flange helps keep chain grime off the rear tire.  

Mounting hardware included. 

A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.

This is the brace needed to stabilize the big front fender on the XR650L. This simple bolt-on brace reduces wind buffeting at highway speeds. It also helps carry the weight of a fender mounted tool bag.

Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included hardware.

This is the brace needed to stabilize the wing like structure they call a front fender on the KLR – both generations. This simple bolt-on reduces wind buffeting and increases steering stability at highway speeds. It also helps carry the weight of a fender mounted tool bag.

Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included stainless steel hardware.

These mounts provide a 1.0″ drop and 1.0″ shift to the rear which lowers your center of gravity and puts you in a better position of control especially when standing.

They are precision fabricated in Oregon. The icing on the cake, they are 0.5 pounds lighter than the factory peg mounts.

Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.

These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.

Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.

Low peg mounts from JNS Engineering. You can use your stock pegs or aftermarket pegs with these T7 mounts.

These offer a 24mm drop & 24mm rearward offset.

Note: Not compatible with any center stand.

These low peg mounts will drop your footpegs 1.5" and move them to the rear 1" for a much more comfortable riding position, especially for taller riders. Unlike relocation plates, these mounts do not hang dangerously below the frame. You can mount stock or aftermarket pegs and they are compatible with all skid plates, crash bars, and center stands.

New 10.9 high strength mounting bolts are included. Once installed the foot controls will need adjustment and the brake switch spring will need to be slightly modified.

Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.

All hardware is included for a quick and easy installation.

This guard is designed to protect your TW200 headlight from rocks, branches, and any road/trail debris kicked up by the vehicle in front of you.  It’s a one piece laser cut steel component with a sleek black powder coat finish.  Mounting hardware is included. 

Note: installation requires drilling two 1/4” holes in your plastic headlight fairing.

This kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

The headlight features two primary sets of LED projectors, a wide low-beam pattern with distinct upper cutoff and a center spotlight high-beam for long range visibility.

The low-beam consumes 20W and remains powered when the 15W high-beam is fired. There is also a daytime running light feature which can be powered for additional glow. The LEDs are rated for 50,000 hours and operate at a 6000K color temperature.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

Non-DOT

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 2008-2018 Yamaha XT250. The new design for the black headlight produces more light and has much more uniform beam pattern when compared to the previous version. New design currently only available in black, chrome may be available in the near future. No wiring, soldering, resistors, trimming, drilling, or fabrication required.

• Low Beam: 20W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

This kit is available with either a chrome or black chrome reflector in the headlight.

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

Now available with a black chrome reflector!

Check out the images below for stock vs. LED patterns and brightness images.

  Fits '87-'07 only

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, drilling, or wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

This kit is available with either a chrome or black chrome reflector in the headlight.

Check out the images for stock vs. LED patterns and brightness. (Images are of a DR/DRZ unit, but the light unit is the same as that on the XRL.)

This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

• Low Beam: 20W, 2,800 Lumens
• High Beam: 35W, 3,600 Lumens
• Color Temperature: 6,000k
• DOT & SAE Compliant
• CE, RoHS, ISO9002, IP67

This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67

No cutting, drilling, or wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

  Please note that this product is not compatible with the 1987 TW200.

This LED headlight from JNS Engineering is DOT approved and an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and mostly plug and play. The DOT kit does not have a daytime running light (parking light) and may require minor trimming on the backside of the fairing. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb. The primary advantage of this kit over the original is the DOT/SAE markings and a wider high beam pattern.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

This new and improved DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware. No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

We highly recommend this kit over the non-DOT and original DOT kit.  The low beam has extra punch and a proper beam pattern cut-off.  The high beam throws light far and wide.  It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

Low Beam: 20W, 2,800 Lumens
High Beam: 35W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

Please note: Fits '87-'07 (Gen 1) only

Good News: There’s finally a plug & play LED headlight conversion kit for your 2008-2020 WR250R and WR250X!

This kit includes a sealed LED headlight assembly with plug & play electrical connection, adjustable powder coated steel mounting bracket set, and mounting hardware. 

Installation is a five minute, one beer exercise. If you can change a residential light bulb you will have no problem installing this conversion kit. We promise.

Please note that you will need to reuse your OEM upper headlight mounting grommet and two aim adjustment springs.  Or add new ones to freshen up your whole headlight unit.

Low Beam: 2,100 Lumens, 20 Watts
High Beam: 2,800 Lumens, 30 Watts
Operating Voltage: 10V-30V DC
Color Temp: 6,000K
Lifespan: >50,000 hours

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow. The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow.  The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

This is the ultimate headlight upgrade for your XT250! It’s a plug & play kit which includes the newly released Morimoto round headlight with preassembled aim adjustable mounting bracket set. Installation takes five minutes and the light output is phenomenal.

Low Beam: 2,400 Lumens, 20 Watts
High Beam: 4,300 Lumens, 35 Watts
Color Temperature: 5,000K
Warranty: 5 Years

This kit includes the all new Morimoto 4×6 LED headlight and a pre-assembled JNS Engineering adjustable mounting bracket set. Like the rest of the JNS headlight kits, installation is a simple 5 minute plug-and-play procedure.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform/controlled, and features a proper upper cut-off. The high beam is amazingly bright, eliminating the need for auxiliary lighting (money saved!). Plus the 5,000K color temperature is extremely easy on the eyes. The materials, construction, and aesthetics are all top notch.

It’s a next level headlight, you won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a one beer, plug & play installation.

This is the best performing and highest quality headlight they currently offer.

The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive, ie USA).

The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed!

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive. (USA)

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.

• Low Beam: 25W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

If your aftermarket exhaust is missing heat shield mounting points, this is the easy fix you’ve been waiting for. 

Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.

Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.

An Oil Cooler Guard we can get behind. Laser cut from 0.125" thick 5052 aluminum, CNC formed and powdercoated black.

Designed to fit the stock mounting holes perfectly, most riders will have this in place in minutes. Don't get stuck in the middle of nowhere with a punctured oil cooler.

This DR650 Oil Filter Guard is CNC machined from solid 6061 aluminum, black anodized, and then custom laser etched with our logo.

It fits over the fragile OEM magnesium cover and provides great impact protection in the event of a tip over.  Proudly made in the USA. 

This radiator guard is as beautiful as it is effective. Keep your coolant where it belongs with this laser cut 0.100″thick hunk of 5052 aluminum. It is laser cut, CNC formed and then powder coated black.

This protector mounts to the front of the radiator in mere minutes using the stainless steel hardware that is included with the guard.

Double the size of your side stand footprint and half the chances of your KLR tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount.

Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.

The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.

Double the size of your side stand footprint and half the chances of your XR650L tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount! All hardware provided.

This is one of the toughest skid plates we've got. Manufactured from 3/16" aluminum that is laser cut and CNC formed, all joints are welded on both sides. The rear mounting bolts are fully recessed for protection. A welded block protects the bolt heads from being bashed and rounded from obstructions. Rubber isolators between the plate and the frame at these two bolt locations help to eliminate vibrations and keep noise down. Front mounts clamp around the frame for a solid connection.

The right side of the plate extends up to cover the oil filter and unbolts from the skid plate for easy filter changes. This skid plate has a black textured powder coat finish for great looks and durability. Includes stainless steel hardware.

This is one of the gnarliest skid plate made for the KLR. Made from 3/16" aluminum, it is laser cut and CNC formed. All seams are welded on both sides and the entire plate is black texture powder coated. Includes all the mounting hardware.

This is one of the gnarliest skid plate made for the KLR. Made from 3/16" aluminum, it is laser cut and CNC formed. All seams are welded on both sides and the entire plate is black texture powder coated. The plate mounts in minutes using stainless steel hardware.

IMPORTANT NOTE: The standard kit will work with all crash bars except for Givi and Happy Trails. Select the Givi option for that brand. This plate will not work with the Happy Trails crash bars.

Select the optional heavy duty mounting brackets if you want to replace the wimpy stock mounts with steel brackets.

Select these optional heavy duty mounting brackets if you want to replace the wimpy stock mounts with steel brackets.

A precision fabricated bolt-on swingarm extension for the TW200.

This kit provides a 3” stretch without having to cut and weld your motorcycle. Heavy duty steel construction with a silver metallic powder coated finish.

This complete kit includes everything you'll need: mounting hardware, brake linkage extension, and a new longer 428x136L non o-ring chain.

Provides additional clearance for running larger ATV tires.

Increase your fuel and/or water carrying capacity. This mounting plate attaches to the OEM Suzuki rear rack and accepts the standard RotoPax mounting pedestal. The use of pressed-in threaded mounting hardware allows for quick and easy installation of the plate and pedestal. When not needed the RotoPax pedestal can be quickly removed and the tidy JNS mounting plate left in place.

• 0.125" 5052 Aluminum, Laser cut / CNC formed
• Powder coated black
• Includes stainless mounting hardware

Order alone or with RotoPax Mount and Water or Fuel container. Get everything you need at one time.