Cogent Dynamics

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are recommended to get the full potential of the DDCs.

You can adjust the preload on your KLR shock easily, why not on the forks as well? These caps give you the capability to adjust the spring preload in your forks to match your load.

Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. Designed by Rick at Cogent Dynamics on his high-tech suspension dyno, then tested and endorsed by KLR owners all over, these units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the units under the springs and hit the trails.

If you weigh up to 250 pounds, select the .64 spring kit. If you are over 250 or carry lots of luggage, please select the .70 spring kit. Please call if you have any further questions.

All of these kits include DDCs, springs, fork oil and preload spacers.

Developed by the KLR suspenison experts at Cogent, this set of springs will stiffen up that wimpy KLR front end. Choose between .64 kg/mm springs (60% stiffer than stock) or .70 kg/mm units (75% stiffer than stock).

A dual-rate fork spring for the early KLR650. These springs start with a .40 kg/mm winding and after approximately 20% of the stroke, stiffen up to .60 kg/mm for the remainder of the travel. A very nice improvement over the stock springs which are .40 kg/mm for the entire travel.

The Moab shock from Cogent Dynamics will change how you feel about your KLR. You may like it now, maybe even like it a lot, but you will absolutely fall in love with it once you mount up a Moab shock.

Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. Ride heavily loaded or with a passenger regularly and you will probably want the Heavy-Duty spring.

For a true comfort and performance package, we highly recommend upgrading your front suspension at the same time.

The Moab shock from Cogent Dynamics will change how you feel about your GEN 3 KLR650. You may like it now, maybe even like it a lot, but you will absolutely fall in love with it once you mount up a Moab shock.

Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. Ride heavily loaded or with a passenger regularly and you will probably want the Heavy-Duty spring.

There is very limited manual preload adjustment access on the Gen 3 KLR650 without removing the shock. Therefore, the addition of the Remote Preload adjuster gives you the convenience of optimizing your rear suspension spring preload for quick leveling (load compensation) of your bike to accommodate a passenger, luggage or just to change ride characteristics based on your preferences.  The adjustment which would normally require reaching the shock in your bike to turn a threaded collar using a tool can be easily adjusted by twisting a remote knob which uses the convenience of hydraulics to change the spring preload up to 100% (9 mm total range of preload change).

There is a mounting conflict for the Remote Preload adjuster with the Happy Trails and T-REX crash bars.

The Moab Pro-Series shock from Cogent Dynamics is the standard by which all other shocks are judged in the KLR world. With its superior performance and exceptional reliability, Moab Pro-Series shocks have literally conquered the world many times over. The staff at Cogent is as passionate about motorcycles as you are.

Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. If you regularly carry luggage boxes and/or a passenger and weigh over 250 pounds, you will probably prefer the Heavy-Duty spring. Call if you have any questions.

Because of the limited space with the reservoir, adjusting your preload is just about impossible and for that reason we only sell these units with the Cogent Hydraulic Preload Adjuster already installed!

For a true comfort and performance package, we highly recommend upgrading your front suspension at the same time.