Search Products

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

Race Tech has developed these fork springs specifically for the heavier weight of the KLR650.

Sold in pairs.

• The .70 springs are 75% stiffer than stock and will be a great choice for most riders
• The .80 springs are 100% stiffer than stock and will be a better choice for heavier riders

Not for 2014-2018 New Edition

Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass.

Straight rate springs will give better control in the rough stuff. Sold in pairs.

In stock form, the forks, featuring a single spring design are under sprung for any rider over 100 pounds. With limited travel, adding a stiffer spring in the right leg only per the stock design was not a viable option.

Race Tech instead offers a High Performance Spring Kit that adds a stiffer spring to the other fork. (The overall spring rate in the forks is the average spring rate between both legs.) This upgrade will make a drastic improvement in handling for most riders.

0.50KG/MM KIT

Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.

• Bushings are dyno-tested to 500,000 strokes with less wear than OEM bushings
• Kit includes two slider bushings and two leg bushings
• Kit includes all copper washers and O-rings
• Kit includes two fork seal snap rings

• Lighter and stiffer than stock, high quality shock spring.
• A proper rear spring will give a smoother more controlled ride.
• Available in a multitude of spring rates, one is the perfect fit for your bike and riding style.
• Stock spring is rated at 5.3 kg/mm for the CRF450L

This adapter set is required to fit an aftermarket spring to the Vstrom shock

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Sold individually.

The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads.  The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.

• Made from super tough glass reinforced zytel
• Reflector Dimensions: 5.25" x 3.5" (135mm x 95mm) 
• Overall mirror length: 7" (175mm) (not including arm mount)
• Convex lens meets SAE and CE specifications 
• Mirror mounts to any 10mm perch.

The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression. 

The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters. 

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends

A quality replacement speedometer cable.

The elegant, open-end design makes these heated grips both stylish and functional. Highly efficient design, delivering warmth faster than traditional heated grips. Five-level temperature controller adjusts the grips accurately to avoid overheating. Specially selected rubber material resists the outdoor environment and provides a secure and comfortable grip. Even at high-temperatures, the grip remains resistant to damage. 

• Removable end caps allow for use as open-ended grips when needed
• For twist throttle applications
• Note: 12-Volt DC applications only.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.

This clamp comes with 1-1/8" handlebar mounts.

Original Kawasaki factory replacement levers for your KLX230.

Replacement folding shift lever, stock length made by IMS.

This kit is for those of you looking for a bit more arm room and a better platform for your feet in the TW cockpit. Included are ProCycle Wide Foot Pegs and our oversize bars with 30mm risers.

• ProCycle Wide Pegs are wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 30mm Moose risers that raise the handlebar 30mm.

Kit does not include new throttle tube. If you have 2001 or newer TW200 and would like a new billet aluminum throttle tube, please select the addon box to receive one with your order.

Here's a UNI dual layer foam air filter element to fit our TW200s. Needs to be treated with air filter oil like any other foam filter.

Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage

Features:

• Coarse open-pore foam catches airborn dirt, grime, and sand
• Fine open-pore inner foam acts as second filter to trap the smallest particles while ensuring maximum air passage
• Adhesive withstands repeated cleaning
• Smaller than stock to increase air space and circulation around filter
• exclusively formulated adhesive withstands repeated cleaning. even with harsh solvents or gasoline
• twin air filters are slightly smaller than stock filters to increase air space around the filter and improve circulation

• Designed to fit in the factory air box exactly like original filter
• The best selling replacement air filter for competition motorcycles and ATVs
• Unique two stage design allows for easy and complete cleaning
• Dual layer of foam, can be serviced separately
• Thin Ultra Seal base is virtually impossible to tear and has a built-in "Grease Groove"

Yamaha uses this seal material in many places on several motorcycles. It is like weatherstripping and is used to seal up the edges in the TW200 air-box. It seals up the air-box so that water and grime can't enter the air-box from the side. Ensures that air entering the box comes from up under the seat.

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

Available for stock gearing, 45 tooth rear sprocket

The 50 tooth rear sprocket will give you much lower gearing for off-road use. You will need a longer chain for this rear sprocket, please order the 130 link chain to fit with this larger sprocket, it may need to be shortened to fit correctly.

These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

Genuine Kawasaki Rear Sprocket.  Size 57T

• Constructed of the highest quality 1045 high-carbon steel
• Exclusive heat treatment and quenching process for strength and durability
• Nearly all machines come equipped from the factory with this sprocket
• The strongest, longest lasting steel replacement sprocket available

• Computer-designed to achieve ultimate strength at minimum weight
• JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
• Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
• Sprockets are heat-treated and bead-blasted to reduce material surface tension
• Unless noted, front sprockets are made with C45 steel and SCM415 chromoly steel alloy; rear sprockets made with top-quality-grade C45 high-carbon steel

The Acerbis 2.0 Chain Guide Block easily replaces the entire OEM unit and ensures durability and high resistance to shock and wear from the chain.

Made of PA6, it is made of two parts that allow installation without removing the chain.
100% PA6 construction Weight: 200 grams

Genuine Kawasaki replacement chain guide. This guide mounts to the lower swing arm.

The RS-2 is a potent and versatile design that evolved from the original TRC, engineered to provide increased power and power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core - and it offers the added bonus of outstanding performance in a value-priced package.

• Diamond-shaped Stainless steel sleeve for increased durability.
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• Weight: .39 lbs lighter than stock configuration
• USFS Approved spark arrester included

The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.

You may want to consider a new exhaust gasket that goes between the header and the muffler.

The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.

• Uses long-life muffler packing for increased packing life
• Forest Service approved spark arrester

Delayed stock from manufacturer, please ask for availability.

Benchmark’s Folded Recreation Maps were created for outdoor lovers who want the high quality recreation information in our atlases but with the convenience of a traditional folding map. Complete public lands detail and hunting unit boundaries are shown as well as categorized recreation listings.

Limited to stock on hand

For the DR650 that has been lowered or converted with supermoto wheels. This stand is 1.5" (40mm) shorter than the stock unit.

Includes a rear shock mount cover plate and plug for lowing the stock shock.

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Shortens up to 1.5" from stock kickstand length
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Extends approx. 0.5" longer than stock and shortens up to 2.5"
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Extends approx. 0.5" longer than stock and shortens up to 3.5"
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. Extends approx. 1" longer than stock and shortens up to 2"
• Material: Steel tubing with black powder coated finish for strength and durability

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. 
• Material: Steel tubing with black powder coated finish for strength and durability
• 2008 - 2018, 2023+ KLR650 S (Lower 1", Raise 3.5")
• 2021 - 2022 KLR650 (Lower 3.5", Raise 1")

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. 
• Extends approx. 0.5" longer than stock and shortens up to 4.5" for the KLX300
• Extends approx. 3" longer than stock and shortens up to 2" for the KLX300SM
• Material: Steel tubing with black powder coated finish for strength and durability

Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz

Kit Contents:

• Two pivot tension springs
• Two lock nuts
• Two washers
• Six o-rings
• Two split pins
• Pivot Pegz sticker and instruction sheet

Replacement Cleats for use with Fastway Pegs.

SW-MOTECH has specially built this centerstand for the Honda Transalp XL750.

The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.

• Stands securely when traveling with lots of luggage and during maintenance
• Bike-specific design for easy mounting and high cornering clearance
• Easy to lift up the motorcycle
• Outrigger for optimal leverage
• Best corrosion resistance due to sand blasting and powder coating of the surface
• Made of robust steel

Cat Crap is the #1 voted anti-fog on the market. Lens cleaner and anti-fog in one. Works for all lenses, eyewear, goggles, helmet visors, etc.

We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.

But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.

Shinko 700 Series tire features an aggressive 60% on-road and 40% off-road read pattern for good dirt riding performance, without sacrificing pavement grip. Other features:

• Aggressive tread pattern with drop lug construction
• Heavy-duty 4-ply carcass for durability
• Reinforced side knobs for cornering stability
• DOT approved

The GP-1 Dual Sport Tire from IRC is designed to provide the best possible handling and control for both on and off the pavement. Special knobs penetrate loose surfaces for excellent traction, braking and cornering off the road yet won't wear off as fast as a full knobby when used on the street. Features include:

• Innovative knob design offers excellent off-road bite
• Won't be shredded on the highway like full knobbies
• DOT approved, 4-ply tire 90% on road, 10% offroad
• All GP-1's are Tube type tires and P rated (max speed of 94 mph)

Available for Front 3.00x21 only

We like red high temperature silicone for use as an adhesive. 

It is much stronger and sticks better than the standard stuff.  It is sensor-safe, low odor, non-corrosive, non-flammable, and non-toxic. 

The resistance to temperatures up to 650°F is a bonus. Comes in a 3 oz tube.
 

No Toil rim grease is a high viscosity, non petroleum based compound specially engineered to provide the ultimate filter rim to air box seal. 

Designed to withstand temperatures up to 300° F, it remains waterproof and dust-proof, keeping damaging dust and water from being drawn past your filter

• Biodegradable
• Non toxic, Waterproof
• Easy cleaning in seconds with water and No Toil cleaner

Eliminates the stock speedometer drive for those who have replaced their stock unit with a Vapor or something similar. Light weight billet alloy spacer and a seal to protect your wheel bearings.

Contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

This Waterproof First Aid Kit is the perfect size for your "Don't leave home without it" list.

Always keep your first aid kit handy and right where you left it. The Waterproof First Aid Kit easily mounts almost anywhere you need it with self-adhesive hook-and-loop mounts. Contents stored in a heavy-duty nylon bag, with waterproof zipper and special coating to ensure your supplies stay dry.

Sintered Pads from EBC provide great performance in all conditions yet still give you long pad life. Front pads are double H rated for maximum breaking. Rear pads offer maximum durability and excellent braking performance.

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

This box moves up the rev limiter allowing higher revs. It also has a hotter advance curve from the OEM box. This allows for a bit crisper throttle response and easier starting. This is a "must have" for modified KLX110's.

• Raises rev-limiter 1200 rpm over the OEM ignition
• Hotter advance curve for better performance
• Direct replacement for the OEM CDI ignition box

Keep yourself COOL with a set of Moto Hoses. Moto Hoses are what you need to handle the heat that your bike is putting out whether you're pushing it to the limit or just stuck in slow city traffic.

Each Kit Contains:

• Color matched carb vent hoses
• Color matched fuel line
• Color matched coolant overflow hose
• Moto Hose is used by Rock River Yamaha and Honda of Troy motocross teams
• Moto Hose for the WR250R/X is available in Blue or White

The Neutral Sending Unit "NSU" on the DR650 can be a problem. The factory screws tend to loosen over time. You really would not want them to get loose in your motor! The permanent solution is to safety wire them. We looked high and low and finally found pre-drilled screws in the correct length and thread pitch. Here we offer a complete kit to take care of those pesky screws.

If you don't do this, you don't have a screw loose, you have TWO screws loose!

Kit Contents:

• 2 drilled stainless steel screws
• Plenty of safety wire
• Wire twisting tool
• New lock tab for the clutch hub
• New clutch cover gasket

The Complete Doohickey Replacement Kit features the Doohickey supplied by Eagle Manufacturing, a torsion spring accompanied by a drill bit, a generator cover gasket, and an exterior cover gasket. Additionally, it includes all necessary components for rotor removal, along with a replacement bolt for reassembly.

Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

Superior Filtration:

Honda recommends replacing this oil filter screen every 7500 miles.

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

ProCycle 425cc BIG BORE 88mm KIT With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), HotCams stage 1 performance camshaft and gaskets. No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.

B&B Off Roads Honda XR150L bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

Select these optional heavy duty mounting brackets if you want to replace the wimpy stock mounts with steel brackets.

Additional protection against rocks and contact with the ground for the engine: the high-quality, aluminium alloy engine guard shows what it's capable of off the street, but provides extra safety and an individualized look on the streets, too. State-of-the-art production gives these bike-specific protectors a secure fit. The installation on frame mounting points lends additional stability and allows for easy installation.

• Underbody protection against stone chips and collisions
• Reliable and easy installation on original attachment points, modifications to the motorcycle are not required
• Bike-specific development for perfect fit
• Mounting material included in delivery
• Durable design made of high quality aluminum alloy

This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.

This ultra tough guard is constructed from 1/8" aluminum and is easy to install.

All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included. 

• Powder coated black (shot peened look)
• Fully welded construction
• Rigid 4 point mounting system
• Hardware and detailed instructions included

THE LUGGAGE RIGGING POSSIBILITIES ARE ENDLESS!

This kit will set you up with the full Green Chile Adventure Gear treatment. You will be able to haul up to four bags of your choice. One system that can be rigged for day trips and easily scaled up for an expedition or extended trip.

No expensive bags required. Any bag becomes motorcycle luggage.

Don't have a rack on your bike? No problem! The flexible soft rack system attaches easily to fenders, footpegs, sissy bars, or your existing rack. Just tighten up the sturdy cam buckles and you're ready to get rigging! Use the versatile combination of runner loops, tensioner straps, and velcro loops to affix any bag you please to any one of over 60 daisy-chain style contact points.

Contruction Features:

• 1" Tubular climb-spec nylon webbing
• Daisy loops along sides and rack surface
• Heavy Duty cam buckles on each corner
• Tensioner loops to keep your luggage secure as you travel
• Ability to carry two bags on the back and two bags on the side.

This Kit Includes:

• 1 Uprising Soft Rack Base
• 2 Soft Rack Side Straps
• 6 Cam Tension Loops
• 2 Ring Tension Loops
• 2 Ring Loops
• 2 Six Foot Runner Loops
• 4 Four Foot Runner Loops

Nomadic Rack for the TW200. CNC laser cut from 3/16" 5052 aluminum with a large 12 x 10-7/8 mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with a 4 point mounting system with no modifications required. There are multiple strap slots for securing gear bags and cargo. Doubles as a grab handle or tow bar. Is compatible with RotoPax mount. All hardware and instructions included.

You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.

Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.

Low profile allows for easy seat removal.

Features:

• 12" long by 10" wide
• Integrated turn signal mounts
• 16 strap slots for securing cargo
• RotoPax mounting kit compatible
• All hardware and instructions included

Note: Placement of this top rack does require removal of the stock tool bag.

Secure storage of a spare tube, tire irons, or random miscellaneous items is a must for any trail ride or adventure. The OBR ADV Gear Fender Bag is constructed from a heavy duty industrial grade ballistic fabric that secures tightly to any fender via oversized heavy duty gutter hooks. The OBR ADV Gear Fender Bag also utilizes an optional double button snap system that when used eliminates any potential for shifting of the fender bag when riding off road or over rough terrain.

Features

• Heavy Duty industrial grade material construction with high strength UV resistant nylon webbing
• Heavy duty dust resistant #10 coil zipper with cover flap 
• Secure attachment with oversized heavy duty gutter hooks
• Optional secondary button snap retainment system
• Sized to fit most HD 18” or 21” tubes

Constructed from heavy-duty waterproof tarpaulin with durable heat welded seams. This coated material makes clean-ups a breeze. Roll-down tops create a waterproof seal and are held in place with heavy-duty ITW quick release buckles. Wide support straps are adjustable via hook and loop material to fit almost any width seat.

• Available in 20 or 30 liter capacity
• Sold in pairs.

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use stock mounting positions as well.

This clamp comes with 1-1/8" bar mounts that work perfectly with the tapered handlebars included. Then there is a new set of ProGrip 714 Rally Grips.

• Interchangeable tips to fit 8 sizes of spoke nipples.
• ( 5.6 / 5.8 / 6.0 / 6.2 / 6.4 / 6.6 / 6.8 / 7.0 mm )
• Main shaft is CNC precision machined from 7075A aluminum and designed for optimum grip.
• Tips are made of heat treated steel for strength.

Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for wherever your adventure takes you! This tank is made from POLYETHYLENE CROSSLINK for extra strength and durability.

DOES NOT FIT NEW KLX300 "R" Models

• High-density polyethylene gas tanks offer maximum fuel-carrying capacity
• All tank colors match OEM colors
• All necessary hardware included (tank decals not included)

The cush hub (sprocket carrier) bearing leads a tough life. This is especially true if your cush rubbers get old and soft. They can allow the chain to pull the cush hub sideways putting a twisting load on the bearing. If there's any question about the condition of your bearing replace it now with this double sealed bearing and quality seal.

Motion Factory Racing patented Flex-Mount Footpeg System provides superior grip and allows your foot to flex forward and back with the movement or your motorcycle.

One of the key features of Flex-Mount Footpegs is their unique flex-mount design. This design allows the footpegs to absorb shocks and vibrations, reducing fatigue and improving overall comfort during long rides. Additionally, the adjustable height and angle options ensure a personalized fit, allowing you to find the perfect riding position for maximum control and stability.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

They put an a90 bushing on all new mount setups so people can get a good feel for their mid range option. The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

Complete mount system includes: 

• 6061 Aluminum ADV Platforms (65mm wide x 107mm length) 
• Stainless steel mounts
• Sleeve bearing (8x10x20mm) included for 8mm OD' footpeg pins. 
• Right and Left spring included. 
• Chromoly steel spindles with reusable thread locker. 14mm wrench. Torque spec 40 ft/lbs 
• A90 (medium flex) rated bushings
• Cleats and stainless steel machine screws. M3x18mm. These can simply be replaced by going to your local hardware store when damaged or worn out. 
• Bushing bolts. 8mm Allen wrench. Torque spec 30 ft/lbs

 They designed their hardware to bend rather than break in a significant impact. A wrench or adjustable wrench will quickly and easily bend the bolt back straight. Please avoid using a hammer. A little leverage from a long-handled wrench or pipe will do the job. The whole system is rebuild-able and serviceable.

They Fit Kawasaki KLX110 and Yamaha TW200 however some of these bikes may need a little modification by yourself, Please check the size carefully before you buy. If you make mods to the footpegs for fitments it will void all warranties and return policies. 

• This high quality SAE to USB-C and USB port adapter features a switched on/off digital voltage display, allowing you to power your devices with either USB or USB-C charger cables
• It comes with a cover for the USB and USB-C ports when not in use, and 2 zip tie slots (zip ties not included) on the back for securely attaching the adapter to your vehicle
• Its size of 3" x 1-1/4" x 3/4" and protective outdoor rating makes it the ideal solution for your vehicle to charge phones or devices producing 5V at 3.1a power
• Easy install to your SAE battery connector cable
• Crafted from durable ABS plastic
• Standard USB port
• Cables and adapters sold separately 

This replacement lens has a clear panel on the bottom to illuminate your license plate. 

Allows you to bolt your license plate directly to the rear fender. 

Does not fit Australian DR650.

Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack

Recommended to use resistor for proper turn signal flash rate.

Specifications

• Comes with mounting hardware.
• Measures 4" long with base and 1" wide at the lights.

Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.

Bike-specific light mounts made of powder coated steel allow easy installation and maximum stability, even off-road. Includes mounting material and instructions.

This listing is for the mount only, no lights included.

The genuine factory shop service and repair manual. This is the reference manual Suzuki dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your DR650.

Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.

Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.

• Even and Accurate Lubrication: Their patented dispenser features exit holes that align with your chain's link plates, ensuring the areas that need it most get it.
• Minimize Over-spray: Keep your motorcycle clean and free of messy chain lube.
• Reduce Waste: No more over-lubing your chain. Their patented dispenser enhances the efficiency of your lubricant use.
• Rotatable Dispenser: Allows you to adjust your hand positioning. Ideal for bike's with chain guards.
• Durable: Constructed from glass-filled nylon, Oinker is strong, durable, and resistant to chemicals.
• Universal Compatibility: Fits any standard can of lubricant.

*For cans with an attached smart straw, you will need to replace it with the included nozzle

What's Included:

• 1 Chain Oiler
• 3 aerosol straws
• 3 replacement nozzle to be used only on cans that have attached straws.

Honda XR650L rear shock upgrade. The experts at Cogent Dynamics know suspension! A proven performance rear shock for your XR650L for use under the most demanding conditions and on the roughest terrain worldwide.

Damping rates optimized to your specific needs, giving you the best ride comfort, traction and control. Frequency and velocity sensing valving works great over wide ranging conditions. Low internal friction. All CNC machined components for top quality and performance. Compact and rigid design with internal separator piston. Adjustable for spring preload and rebound damping. Fully serviceable shock is designed for the long haul.

 *Spring color may vary due to specification requirement and availability.

Good News: There’s finally a plug & play LED headlight conversion kit for your 2008-2020 WR250R and WR250X!

This kit includes a sealed LED headlight assembly with plug & play electrical connection, adjustable powder coated steel mounting bracket set, and mounting hardware. 

Installation is a five minute, one beer exercise. If you can change a residential light bulb you will have no problem installing this conversion kit. We promise.

Please note that you will need to reuse your OEM upper headlight mounting grommet and two aim adjustment springs.  Or add new ones to freshen up your whole headlight unit.

Low Beam: 2,100 Lumens, 20 Watts
High Beam: 2,800 Lumens, 30 Watts
Operating Voltage: 10V-30V DC
Color Temp: 6,000K
Lifespan: >50,000 hours

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.

Fits 520, 525, and 530 pitch chain.

A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.

Stock OEM works with factory rotors, comes in a pack of 6.

For aftermarket rotors like Warp 9 or EBC front and rear sets are available.

Front comes in pack of 6
Rear comes in pack of 4.

Special tool to remove the flywheel/rotor from the end of the crankshaft. You have to remove the flywheel/rotor to upgrade the doohickey.

The 12oclock Labs EXUP Emulator is used in place of the stock exhaust servo motor when you replace the stock exhaust with an aftermarket exhaust system. The microprocessor controlled EXUP, emulates the exact characteristics of the stock exhaust servo motor and its motor delay sweeps, keeping the ECU from displaying the dreaded check engine light. Weight is less than 1/2 an ounce and it is a direct plug and play replacement.

Give your Honda the ultimate protection with B&B Off Road’s heavy-duty chain guard. This premium upgrade replaces the stock plastic guard, notorious for bending and breaking on tough terrain.

Crafted for Unrelenting Performance:

Precision-machined from robust 2.5mm marine-grade aluminium, this chain guard delivers unparalleled strength and durability. Say goodbye to worries about trail debris or rogue rocks damaging your chain – this guard stands strong against anything you throw at it.

Lightweight Design, Maximum Protection:

Despite its impressive strength, the chain guard is engineered to be lightweight, minimising any additional weight on your bike. This meticulous design ensures optimal performance without sacrificing protection.

A Perfect Fit:

This B&B Off Road chain guard seamlessly integrates with your Honda CRF, eliminating any installation hassles. The precise CNC machining guarantees a perfect fit for each compatible model.

Invest in Peace of Mind:

Protect your chain, a vital component of your motorcycle’s drivetrain. By preventing damage from debris and impacts, this chain guard minimises the risk of breakdowns and costly repairs. Hit the trails with confidence, knowing your CRF is shielded for the long haul.

Keep track of your keys easier with our embroidered patch on a keychain.

Finished with metal ring with eyelet and merrowed border.

Patch measures 1.5" x 5"

Zero Gravity windscreens feature the finest optics of any windscreen on the market. All Zero Gravity windscreens are fabricated using highly specialized "vacuum forming" techniques similar to those used to form aircraft canopies. The result is a virtually distortion free optical lens.

Made from the finest grade of acrylic plastic, Zero Gravity windscreens are stretched as they are formed, a process which results in superior strength and flexibility. This flexibility allows the windscreen to absorb road vibrations and resist cracking. All of our windscreens are factory pre-drilled and ready to install. The mounting holes and windscreen profile match the O.E.M. windscreen for a precision fit.

Zero Gravity currently offers three types of windscreens for the new version of the KLR.

SR is the Stock Replacement

DB is the Double Bubble screen

ST is the Sport Touring model.

The DB model is approximately 1.75 inches taller than stock and the ST is approximately 3.5 inches taller than the original. Each screen is available in Clear, Smoke or Dark Smoke colors as well.

Top end gasket set  

Missing the head gasket.  Sold as is, picture indicates everything included.