Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
By simply replacing a motorcycle's stock shock linkage with a longer, stronger and lighter DeVol Lowering Linkage, a bike's seat height will be dramatically lower to help give those riders with shorter inseams a more confident and enjoyable ride.
The DeVol Lowering Linkage is not recommended for aggressive riders or jumping. If you need a linkage to enhance the performance of your bike's suspension, the DeVol Transformer Pull-Rod is exactly what you are looking for.
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.
Kit includes all the fork bushings, o-rings, snap rings and washers this kit comes with what it needs to completely rebuild your front fork bushings.
A high quality replacement clutch cable.
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
G3-LD Gold Valves provide better control for any rider by creating more shim leverage and decreasing the angular shim deflection.
Top suspension performance requires firm bottoming resistance with plushness at the same time. Even the best suspension tuners can only make the stock valving design work so well. The Gold Valve Shock Suspension System is a proven bolt-on shock valving system that improves control, traction, performance and bottoming resistance.
Australian made, this protector bolts to the stock caliper bracket.
Riding height is very important you need to be able to control the bike at all time. So for those riders that find that their bikes are a little bit high, the Zeta Anodized Lowering Link are perfect replacements for your OEM linkage. Lowering your center of gravity in some case gives you better handling and a more comfortable riding height.
FEATURES
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Developed for Baja racing, their comfort model maintains a similar contour to stock at the front of the seat and tapers out towards the mid-point to distribute rider weight over a greater area. The Comfort seat is wider than stock, but not so wide that it would hinder movement in aggressive race situations.
The comfort model strikes the perfect balance between an aggressive race profile and a wider more comfortable seat.
Available as a Foam & Cover Kit for OEM pan.
| Width: | 7 3/4" (197mm) |
| Height: | 1" (25mm) Lower than stock |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Developed for Baja racing, their comfort model maintains a similar contour to stock at the front of the seat and tapers out towards the mid-point to distribute rider weight over a greater area. The Comfort seat is wider than stock, but not so wide that it would hinder movement in aggressive race situations.
The comfort model strikes the perfect balance between an aggressive race profile and a wider more comfortable seat.
| Width: | 7 5/8" (194mm) |
| Height: | Same as OEM |
Rebound Separator Valves replace the shock shaft nut with an asymmetric valve (provides a different flow rate in each direction of travel) to increase traction and improve bottoming resistance and pitch control.
Why is this needed? On a standard shock the Low Speed Rebound Adjuster flows the same on compression and rebound. In testing, when the lowest speed rebound damping is quick enough to get good traction, the lowest speed compression damping is too mushy. This causes a vague feeling and bottoming on long duration hits like big dips or gullies in Dirt. For Pavement RSV's have the added benefit of pitch control (front to back movement during acceleration and braking). This keeps geometry more consistent.
The Valve has a partially drilled bleed hole in the center. IT MUST BE DRILLED BY THE END USER TO THE PROPER SIZE (2.8mm).
CNC’d and formed from aircraft grade 5052 aluminum. Covers and protects the rear brake master cylinder.
50mm step width provides better grip and control
