Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
CNC cut and bent and then artistically welded, these are much more stout that the stock plastic unit. No worries of them cracking and falling off in the middle of nowhere.
Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.
A replacement gas cap for your IMS tank. Newly redesigned to resist damage from new fuel additives that were hard on the seal in the old style cap.
The Speedo DRD corrects and fixes the speed signal after it was altered by something else, such as sprocket changes or tires size changes or transmission changes.
The Universal Kit does require some basic wiring to install. It's fairly easy, and only 4 wires; [positive, ground, signal-in, signal-out]. Universal Kit works for Cars, Trucks, & Motorcycles with digital odometers, and 3 wire speed sensors.
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
Genuine Honda Factory Service Manual specifically for your CRF250L
High quality stator cover gasket.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
Quality steel rear sprockets.
Color may vary based on manufacturer availability, quality will not be compromised.
Genuine Honda replacement oil filter cover gasket.
Includes all necessary top quality gaskets, and seals for engine rebuilds.
Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.
Also works with Edge-2 Circuit Board Upgrade.
B&B Engineering Bash Plate for the CRF250L is made from 5083 4mm aluminum plate. Chosen because of its suitability for welding and extreme abrasion and impact resistance, this plate will protect the valuable center cases and deflect items away from the side cases as well. This plate is supplied with the necessary stainless clamps and bolts where necessary as well as foam or rubber where required.
OEM throttle cable set for the CRF250L
*generic image, actual cables may look different.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.
Order up your new levers here! If you keep breaking levers, you might want to think about a set of handguards to protect them in case of a fall.
Aftermarket foot pegs from our friends at Warp 9. Made from light weight T-6 aluminum and stainless steel teeth. These have an extra wide platform as well as the Exclusive "X" bridge that adds 2 center teeth for added grip.
A high quality replacement clutch cable.
Silver in color
Upgrade your bike with a tapered 1-1/8" bar. Constructed of Aircraft grade 7065 T-6 aluminum that tapers to a standard 7/8" to accept stock controls.
Aircraft aluminum withstands hard hits from logs and rocks. All mounting hardware and wear blocks included.
Constructed of durable 3mm powder coated aluminum and easily installed utilizing existing mounts, the R&G Bash Plate (center plate) will protect the underside of your motorcycle from damage and debris. Add Case Guards (left and right plates) to your order for complete protection.
Constructed of heavy-duty machined steel, aluminum, and high-density nylon, R&G frame sliders provide maximum protection and high quality fit and finish. R&G "Aero" sliders have an aerodynamic teardrop shape for a more streamlined look than traditional cylindrical slider pucks
R&G "Cotton" Reel Swingarm Spools are oversize paddock stand bobbins that perform double duty as lifting points for hook style paddock stands as well as protection for the swingarm of your motorcycle in the event of crash or drop.
We start with Excel or Sun rims, OEM hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.
These bolts are flat head style, requiring a countersunk hole in the sprocket.
50mm step width provides better grip and control
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
These caps fit Acerbis tanks only.
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support.
Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 9 7/8" (251mm) |
| Height: | Same as OEM |
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Fits Honda CRF450L Motorcycles (Front Turn Signals)
OEM Fit Left Front and Right Front turn signal connectors with wires pre-attached.
This kit is specifically for attaching After-Market turn signals to the front of the CRF250L / Rally or CRF450L.
These hand-built units out of Australia are one of the most advanced radiator protection systems available! CNC machined 6000 series three-dimensional aluminium extrusion melded with 5000 series alloy plate to create a system that protects your precious radiator from almost any direction.
Designed with a fin angle that allows almost nothing to come in contact with the vulnerable core that is otherwise directly exposed to roost, rocks and all sorts of trailside debris. The fins are designed in a fashion that they completely mimic the designed airflow characteristics of the OEM plastic protector fins.
The protective finned louver panel quickly and easily unbolts to make clean-up a snap. Three-piece modular construction allows for greater design flexibility which eliminates the compromises that are built into one-piece designs. If any single piece of this unit is ever damaged, it is replaceable by itself, no need to replace the entire guard. Just give us a call. Installation is a snap, taking no more than 30 minutes with basic tools.
Developed on the track and brought to the road. R&G engine case covers are made from 4mm polypropylene for strength, durability and looks that compliment your bike. Both sides included.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
NOTE: LED's must be installed on a 12 V DC system!
Includes all necessary top quality gaskets for top end rebuilds.
Driven engine block off plates will stop the annoying and possibly damaging backfires from occurring while allowing you to remove a few pounds in associated valves and hoses from your bike. On late model EFI bikes with 02 sensors, ESPECIALLY when using Dynojet's Power Commander V with the Autotune feature, the air injection system MUST be blocked as it will introduce additional oxygen into the system which will skew your 02 sensor's values and make it impossible to get a correct tune.
This beautiful polished rear carry rack from B&B Eng. is made from aluminum tubing and 4mm 5083 plate. 5083 is used because of its suitability for welding and high level of abrasion and impact resistance. Kit includes all the necessary stainless clamps and bolts. With the roundness and strength of the tubing supports, it makes a great grab handle when you need to lift the rear of the motorcycle.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters 1-1/8 inch (28.5mm) handlebar saddle clamp set.
What's in the box:
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
