Moose Adventure Windscreen
The shorty screen in 5" shorter than stock shield.
The Parabellum Windshield is both taller and wider than the stock shield offering more protection from wind, rain, weather, and anything else you may come into contact with on your journey. The Africa Twin’s off-road roots are not forgotten by this windscreen. The stock Barkbuster like hand guards clear the windshield at full lock while the shield is forward mounted and upright allowing the shield to work well while you are standing on the pegs and moving around on the bike off-road. On the street, you can expect smoother, quieter, over the helmet air flow while improving fuel economy and comfort. The Parabellum screen for the CRF1000L mounts easily with an included screw kit in the stock location. It's made from 3/16 inch cast acrylic and is 16 inches wide at the top. The windshield is available in clear or tint and 3 different heights.
National Cycle revolutionizes windscreen performance with the VStream Windscreen. The patented "V" shape and advanced dimensional contours push the wind vortex away from your head, resulting in a peaceful, quiet riding environment. The passenger's comfort is improved as well.
Reduced wind noise, less turbulence, superior strength.
Muddy conditions are the bane of ADV bikes with low fenders. Get more clearance between your front fender and tire. Our kit uses CNC machined, black anodized brackets. Lifts the front fender 20mm.
Ultra-Light, Race Inspired Titanium Muffler
Available in slip-on/bolt-on and full system configurations depending on the application
The Yoshimura RS-4 is a proven choice to improve the performance and sound of the Africa Twin.
Removing the stock muffler saves over 4 pounds and makes the 988cc parallel twin engine growl!
The Akrapovic double-flow muffler is made of a Titanium outer shell with a Stainless Steel end cap. The joint on the inlet cap is CNC milled and connected to the inlet pipe with silicon-shielded tempered springs. A lightweight, compact and high-temperature-resistant carbon fiber clamp supports the muffler to the frame.
This muffler is 3 pounds lighter than stock and will give you an increase in power across the powerband.
The plug-and-play exhaust is simple to install without any need for remapping and comes with full instructions.
*NEW OFFERING
The Dynojet Auto Tune kit is an "add on" accessory that can be used with any of our Power Commander V’s. It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install. If your exhaust does not already have one, a "weld in" O2 sensor bung is included.
Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work.
POD-300 Digital Display
Simply connect the included CAN cable and you’re ready to go; there’s no need to tap power or deal with other messy connections.
Two-position map-switching is capable with this Single Pole, Single Throw switch. You can toggle between two different fuel maps quickly and easily.
For Use with the DynoJet Power Commander V
Original equipment replacement 'in-tank' fuel filter.
Traveling where fuel quality will be questionable? Carry a spare fuel filter.
The set includes a 27mm for the rear and a 22mm for the front. Each 10 inch forged steel tire iron has a hex wrench on one end. The rounded spoon end minimizes pinched tubes and scarred rims.
The GPR v5 is the fifth generation steering damper. Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch.
V5-D Fat Bar kit – A Sub mount kit, mounts below the handlebars. Uses the low-profile GPR V5d dirt bike stabilizer in a cradle-style handlebar mount and bolts to the stock triple clamp. Will raise bar height about 1".
These kits include the GPR V5d dirt bike damper, handlebar mount, frame bracket and all mounting hardware.
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
Choose from Excel or Sun rims. Both come with Buchanan's heavy gauge stainless steel spokes and zinc-plated nipples. Rims and spokes are precision machined for a perfect match to your bike.
Complete set of stock size wheels, 18" rear and 21" front. We start with Excel or Sun rims, OEM hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Excel rims are silver only. Sun rims available in silver, black or gold.
Add any set of tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
We start with a silver Excel or Sun rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Excel rims are silver only. Sun rims available in silver, black or gold.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
We start with a silver Excel or Sun rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Link lowers the rear of the bike by 7/8".
Comfortable at a stop or on technical trails.
Installation takes about one hour, and only a few minutes more to drop the forks in the front to match.
This link fits both manual and DCT transmission models.
Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (Velcro) fastening on back side makes installation or removal for cleaning a breeze.
This skid plate is extremely strong, manufactured from a 5 mm aluminum bottom with 4 mm thick side walls, offering complete protection of the engine block. This unit is built with precision-manufactured mounts that fit directly into the existing frame mount, creating a robust connection that distributes the forces not only to the mounting points but also to the bikes steel frame in case of ground contact. 8 mm strong rubber sliders also help to absorb and distribute impact forces. This unit completely replaces the wimpy stock plate constructed from just 2.5 mm material.
In addition to providing better protection and a sliding surface for impacts, this guard also offers better header and exhaust protection. Cutouts for both oil drain screws mean you don't have to remove it for changes. This plate is also compatible with Honda side stand as well as the SW-Motech Centerstand.
Provide absolute protection for your AT by including Crash Bars and the Skid Plate Extension, all made by the folks at SW Motech.
This unit is NOT compatible if with the optional shift lever on the DCT version.
The Safari Bash Plate is a bit bigger and more protective than the Big Tour model. Made from the same 5mm 5083 plate, this plate extends further up the front and around the sides of the motor. There is a specific DCT model that wraps up even further to help protect the important parts on the right side. (See last image.)
Fits with the OEM centerstand, but will NOT work with lower engine crash bars. Will work with Upper Crash Bars from SW-MOTECH, Hepco and Becker and OEM Honda units. Remember, all B&B bash plates are quality built and supplied with all necessary hardware and detailed instructions. Foam or rubber is included wherever it is required.
The Big Tour Bashplate from B&B Off Road Engineering is built from 5mm 5083 aluminum plate providing protection from rocks and sticks and other debris. This plate will work with the OEM centerstand and most crashbars.
If you are headed out for miles of back roads and trails, please consider the more protective Safari model. All B&B bash plates are quality built and supplied with all necessary hardware and detailed instructions. Foam or rubber is included wherever it is required.
Do you have the SW Motech Centerstand and Skid Plate mounted to your Africa Twin? If so, it is a great idea to mount up the Skid Plate Extension. This plate adds protection to the undercarriage where the engine guard ends, giving you a more complete protection system. 3mm thick aluminum plate mounts to tabs that are built into the Centerstand. The Centerstand and the CS Extension function seamlessly together. These two pieces assure that you are completely protected down under. Kit includes Centerstand, hardware and detailed instructions.
Please Note that this Skid Plate Extension is only compatible with the SW Motech Skid Plate and the SW Motech Centerstand.
Three-stage removable, reusable, black nylon push rivets. Comes in a package with 10 individual rivets. The Africa twin has lots of these holding together the body work. They are easily lost or damaged. Carry some spares in your tool kit.
The SW-Motech Centerstand is something that should be an OEM item. Essential for flat tire repairs, tire changes, chain maintenance, oil changes, loading/unloading luggage and many other day-to-day maintenance operations.
Integration with OEM exhaust and sidestand is exceptional. The extended foot lever maximizes leverage making for easy elevation of your Twin. There are no penalties in clearance for these benefits. Tubular steel construction with a heavy-duty black powder coat provides for a stable foundation for supporting your motorcycle. No sacrifices were made to the performance or clearance of the Twin.
Installation is a simple bolt-on procedure; no drilling, cutting, welding or relocating other components for fitment. Package includes all necessary mounting hardware and detailed instructions.
Please Note that the Centerstand works perfectly with the Skid Plate Extension.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm.
Ride once with a set of TechSpec Tank Grip Pads and you won't want to ride without them again. Measuring just .125" thin, you'll feel the difference the minute you throw your leg over and take a seat. The pads improve the relationship between you and your machine! Yep, now you can squeeze it, grip it and rip it!
This precut kit includes right and left grips along with a custom center tank piece that can give you additional grip as well as padded protection. Also reduces abrassion damage to the center area of the tank.
Please note that the two options are made from the same material. The Red/White/Blue set is NOT the color of the Grip Pads, but the color of your Africa Twin. These are cut slightly lower to meld more beautifully with that great paint scheme. If you have any other scheme, please order the Standard Pads.
High Quality chain. Will need to be cut to fit your sprocket combination.
Comes with screw-type master link
