Replacement friction plates.
Aramid High Performance Clutch Disc Sets use aramid to add strength, reduce wear and increase life of the friction material; aggressive riders will benefit from the superior performance of race-proven aramid.
Limited to stock on hand.
High quality steel front sprocket
For reference, the stock gearing for the WR250R is 13/43 while the X model runs 13/42 stock gearing.
Quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Available in a 15T
Available for stock gearing, 45 tooth rear sprocket
Genuine Kawasaki replacement chain guide. This guide mounts to the lower swing arm.
Chain sliders may undergo degradation over time due to the friction produced by the chain's movement. Restore optimal performance by utilizing this authentic Yamaha component.
Radiator guards from Devol Racing protect your radiators from damage due to trail side objects and roost bullets. They offer protection not just from frontal assaults but also from those tricky side attacks. Made from high-grade aluminum alloy for light weight and strength, these guards have an improved air-flow design that eliminates any overheating problem. A solid mounting to the frame make these stronger than most guards that just mount to the radiators themselves.
Devol Racing makes a super product that will keep you on the trail for a long time.
B&B Engineering CNC machines these Oil Cooler Guards from 2.5mm marine grade aluminum. This guard covers the full length of the oil cooler, unlike the stock unit! Select polished finish or a protective black polymer coating.
This skid plate is extremely strong, manufactured from a 5 mm aluminum bottom with 4 mm thick side walls, offering complete protection of the engine block. This unit is built with precision-manufactured mounts that fit directly into the existing frame mount, creating a robust connection that distributes the forces not only to the mounting points but also to the bikes steel frame in case of ground contact. 8 mm strong rubber sliders also help to absorb and distribute impact forces. This unit completely replaces the wimpy stock plate constructed from just 2.5 mm material.
In addition to providing better protection and a sliding surface for impacts, this guard also offers better header and exhaust protection. Cutouts for both oil drain screws mean you don't have to remove it for changes. This plate is also compatible with Honda side stand as well as the SW-Motech Centerstand.
Provide absolute protection for your AT by including Crash Bars and the Skid Plate Extension, all made by the folks at SW Motech.
This unit is NOT compatible if with the optional shift lever on the DCT version.
The Rally Pro X-Strong features a high-impact, composite injection-molded outer guard surrounding an anodized aluminum inner guard. It is equipped with an indexed steel bar-end insert that ensures a secure installation, preventing Rally Pro handguards from slipping, even in challenging conditions. Additionally, a compact integral spoiler is incorporated into the design. The package includes a robust universal silver mount kit that is compatible with 7/8” (22mm), Pro Taper 1 1/8” (28mm), Magura, and Twin Wall aluminum handlebars.
Some models with adjustable windscreens may need the windscreen rotated forward, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.
For Straight 7/8" handlebar
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
This guard is designed to protect your TW200 headlight from rocks, branches, and any road/trail debris kicked up by the vehicle in front of you. It’s a one piece laser cut steel component with a sleek black powder coat finish. Mounting hardware is included.
Note: installation requires drilling two 1/4” holes in your plastic headlight fairing.
High quality aluminum caliper guards from Works Connection protects your brake caliper and looks great too.
Dunlop designed the D606 tire to be street-legal but with an emphasis on aggressive off-road riding and great durability. A full-depth tread pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. At the same time, the D606's tread compound is engineered for good highway durability and grip.
The Dunlop D606 is R rated (max speed of 106 mph)
Dual purpose tires made for 60% street, 40% off-road.
Excellent performance on dirt, gravel and bad roads.
Tube type, S rated (max speed of 112 mph)
The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; their springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerences in the industry. These are the finest springs in the world-guaranteed.
Kit includes required adapter collars
Stock Shock Spring 7.28 kg/mm
Spring color may vary due to specification requirement and availability.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
Adapters are required for this spring.
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
You can adjust the preload on your KLR shock easily, why not on the forks as well? These caps give you the capability to adjust the spring preload in your forks to match your load.
High quality OEM replacement fork seals.
Sold in pairs.
Kouba lowering link will lower the rear suspension 1.75". Comes with bearings and seals installed for a quick and easy installation.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Link lowers the rear of the bike by 7/8".
Comfortable at a stop or on technical trails.
Installation takes about one hour, and only a few minutes more to drop the forks in the front to match.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Kouba lowering link will lower the rear 1.75". Comes with bearings and seals installed for a quick and easy installation. Instructions included.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Complete kit of OEM quality parts to replace the bearings and seals in the swingarm pivot.
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
This kit fits all Nomadic tubular type racks. (All flat stock racks are already RotoPax compatible)
The second image shows the kit, which includes all the hardware and instructions required. The lower image is just an example of what the eXpander looks like mounted to one of their racks.
Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.
While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.
If you want a wider platform for support, consider adding the luggage plate to this rack.
Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series KLX300 rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
You can add the double D ring loop to any 1" flat webbing system. This simple piece adds a lot of flexibility to any luggage system you are using. Instantly and easily create a mount point or adjustment point on almost anything. Double D Rings can be used as a secondary buckle and works the same way as a helmet strap. However, the double D rings should NOT be used as a primary means of securing luggage.
Available in 6 colors.
CONSTRUCTION FEATURES
The glove box for your motorcycle! The Zigzag handlebar bag is their smallest bag yet also one of their most popular. Sometimes you only need the basics like your wallet, phone, registration, and other small items, and no matter what you’re riding, the Zigzag handlebar bag delivers quick and easy access to the basics.
Replace the worn slide guide in your stock Mikuni BST carburetor before it causes additional wear to the needle and needle jet. There are wear indicators on the slide guide that help you recognize when it is time to replace your slide guide. New O-ring included.
A new slide for the stock Mikuni BST carburetor.
Direct replacement for the stock spring and exactly like the old Merge Racing spring. Gives a much more consistent accelerator pump squirt. Eliminates the need for the 'O-ring mod', wire or zip-ties on the pump arm. Fits all Keihin FCR-MX carbs except '07-'08 CRF250/450.
Not for the stock DR650 carburetor Fits FCR-MX conversion Only
This cover acts as an "adjustable leak jet" to fine tune the accelerator pump squirt.
Eliminates "4-stroke bog" when used with correct jetting. Allows the use of correct carburetor settings to optimize performance, starting and reliability. Improved low-end performance with much better throttle response. Investment cast and finished to precise tolerances with internal high volume vertical check valve. Fits all motorcycles and ATVs using a Keihin FCR carb. Easy installation instructions (including online video) and template.
Buy both and save! Includes the Boyesen QuickShot 3 and Sunline Mixture Screw
Designed for use with stock engines using either stock or aftermarket exhaust and air filters.
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Grab our 5-pack and save both time and money!
ProCycle 425cc BIG BORE 88mm KIT With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), HotCams stage 1 performance camshaft and gaskets. No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
Includes 2 drain plugs
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
This is an extended version of the stock DR650 clutch release arm that is manufactured by Suzuki.
Upgrading to a longer clutch release arm will lighten the pull of the clutch lever through means of increased leverage. This means less fatigue, quicker clutch engagement, easier clutch modulation and longer rides.
The extended clutch arm will not offer a drastic change in clutch pull. If you're looking for a major change in clutch pull at the lever, we recommend getting a Magura hydraulic clutch kit.
Our very own high flowing head-pipe is made in the USA using a CNC (computer numerically controlled) mandrel bender for an absolute perfect fit. It is a high quality 3-piece welded two into one, stainless steel head-pipe.
The SS Pro-Flow is a tested upgrade over stock that will bolt right on with no modifications needed.
We recommend a new exhaust gasket when installing your new SS Pro-Flow.
Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
Kit includes two gaskets.
This is the gasket used between the header pipe and the stock muffler. This gasket is not needed for aftermarket mufflers!
The Yoshimura RS-4 is a proven choice to improve the performance and sound of the Africa Twin.
Removing the stock muffler saves over 4 pounds and makes the 988cc parallel twin engine growl!
No longer need your speedo drive? Install an electronic unit? This CNC machined aluminum unit will replace the stock speedo drive on the front wheel keeping things properly spaced and sealed up.
To suit a 20mm Axle.
Before placing your order please ensure you check the diameter of the axle, as the earlier models may have different sized axles.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 1 |
High Quality Replacement Wheel Bearings and Seals for your TW200.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 1 |
The 250 taillight & brake light fits perfectly into the pocket from the stock DR650 taillight on the rear fender. Smaller and much better looking than the original.
Totally 'plug-n-play', includes a standard bulb installed or purchase an LED replacement, sold separate, for even brighter braking. The wire pigtail plugs directly into the DR650 harness just like stock.
Does not fit with the ProCycle Fender
This new and improved DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware. No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
We highly recommend this kit over the non-DOT and original DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
Low Beam: 20W, 2,800 Lumens
High Beam: 35W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67
Please note: Fits '87-'07 (Gen 1) only
This is a plug & play low profile LED light bar kit which includes laser cut stainless steel mounting brackets and high quality wire taps.
IMPORTANT: Must be used in conjunction with LED headlight or bulb that consumes no more than 35W.
Please note that this product is not compatible with the 1987 TW200.
A nice place to mount auxiliary lights on your KLX where they will be high and easy to reach for adjustment but still tight to the cowlings. They will not interfere with controls, body work or the fuel tank.
Constructed of 1/8" stainless steel they are intended for LED lamps in the 2" range, but with a slight slotting of the mounting holes, will work great with 3" lights as well. Includes longer bolts to for the upper triple clamp mounts.
Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.
The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
Each kit includes all necessary rubber components and brake pins.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
The GBrakes steel braided brake lines for the big Twin CRF1000L replace the stock rubber lines to enhance braking performance. Stock rubber lines expand under pressure giving a spongy and inconsistent feel at the lever/pedal.
This kit includes all 7 lines involved in the ABS braking system front and rear. These high quality lines utilize the finest materials available to eliminate expansion: Teflon inner hoses wrapped in 64 strand staInless steel weave, heavy duty hardware and machined fittings. A Crush Washer relief channel provides an effective double seal to stop leakage. Each line is replaced from the master cylinder all the way to the calipers and labeled to help with installation.
All the parts of this kit are designed, engineered, manufactured, tested and quality assured in the USA! All of these parts come with a lifetime warranty. Everything needed is included: Brake Lines, fittings and all necessary hardware and detailed instructions.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
Includes front and rear brake pads.
The Moose Tire Bead Tool holds your tire in place as you work you way around the tire
Made of aluminum with a nylon screw so it will not scratch the rim
Sold in pairs
The MotoPressor is a compact pump unit that weighs only 1.3 pounds and fits in the palm of your hand! Measures 4"x3"x1.5" This makes it smaller and easier to carry with you.
It includes a 8 inch long inflation hose, with a a low air loss chuck. You also get an SAE power cord that attaches to your battery and stays there, along with alligator clips with SAE connector. The Pocket Pump has an 6.5 foot power cord. All of this packs into a heavy duty neoprene pouch.
MotoPressor will inflate a 150/70/ R18 tire from 0-31psi in under 4 minutes, and is capable of pumping up to 130psi. It also features a built-in cooling fan to keep the pump at optimum operating temperature, and a check valve to check the psi by attaching your tire gauge to this valve.
This DR650 Oil Filter Guard is CNC machined from solid 6061 aluminum, black anodized, and then custom laser etched with our logo.
It fits over the fragile OEM magnesium cover and provides great impact protection in the event of a tip over. Proudly made in the USA.
Double the size of your side stand footprint and half the chances of your KLR tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount.
The IMS Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping.
They are the original Cast 17-4 Stainless steel pegs that revolutionized the foot peg market.
These pegs are 50mm(1.95") x 78mm(3.1").
The IMS Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping.
They are the original Cast 17-4 Stainless steel pegs that revolutionized the foot peg market.
These pegs are 50mm(1.95") x 78mm(3.1").
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 10.5" (267mm) |
| Height: | Same as OEM |
If you already have a Quad Lock Case, you can Twist Lock and Go with any of these secure mounts.
Or Choose the Universal Adaptor to use your current phone case.
The Quad Lock® Handlebar Mount is the ultimate smartphone mount for motorcycles, compatible with all Quad Lock® Cases including the Quad Lock® Universal Adaptor for other Android phone devices.
The Quad Lock® Handlebar Mount gives you the flexibility to mount your phone in a convenient and visible location using a rotating head and includes an extension arm if extra clearance is required. With your phone securely mounted to your motorcycle, you can use navigation apps to guide you to your location with ease and always stay connected.
Standard:
NOTE: Case not included
Motorcycle Vibration Dampener is recommended for use with this product.
Hot Shot Series Honda CDI Box; Rick's aftermarket Hot Shot CDI box has a hotter spark than OEM and retains the stock curve. It will replace OE# 30410-MN9-003 & 30410-MN9-000 and fit 1993-2021 XR650L. *CDI Boxes are not covered under the One Year Warranty.
The TAPP™ is a compact, easy to mount, all weather 2.1amp USB Power Port and is the answer for powering and charging your USB devices including cell phones, smart phones, most GPS units, MP3 players, and most digital cameras.
Quick charge 3.0 technology provides fast charging for Android devices with Quick charge capability. Charging power levels up to 18 watts contrast with the USB standard maximum charge power of 10 watts.
TAPP™ 2.1 Amp Weatherproof USB Power Port With Quick Charge 3.0 Technology
Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Includes 2 drain plugs
A 10-pack of drain plug sealing crush washers. Soft tempered aluminum drain plug crush washers designed to seal in fluids
Replace your sealing washer at every oil change to prevent a leak.
Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
The genuine factory shop service and repair manual. This is the reference manual Honda dealers use in their service departments. It has all the necessary info to do maintenance or repairs to your Africa Twin CRF1000L.
Included with the tank:
Does your stock vacuum operated petcock not shut off when your bike is parked? Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks.
Aftermarket plastic tanks might need the hole cut into an oval shape to fit the two standpipes.
Replacement side panels from ProCycle (formerly DSA). These pieces are fully compatible in any combination with the original factory plastic. These side panels have a crisper, more angular look than stock. Vacuum molded, they are a design improvement over the stock panels.
Sold in pairs
Does not include heat shield. Depending on your application and preferences, more than one optional heat shield may be useful.
The easy way to lubricate the cables on your motorcycle. Lubricates completely in five seconds!
Features:
A super compact shovel with several bonus features!
Nitro Tape is a self-fusing silicone tape that's easy to remove with no residue.
It is waterproof, stretches up to 300%, has a temperature range from -65° to 500°F and insulates 8,000 volts per layer.
It resists UV, salt and corrosive chemicals.
20 mil thick, 1" wide by 10' long.
If you've split a radiator hose, this can help. A 'must have' for all tool kits.
A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.
These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!
| Width | Height | Rise |
| 813mm | 160mm | 104mm |
| Clamp Area | Sweep | Control Area |
| 236mm | 100mm | 199mm |
