Search Products

B&B Off Road Engineering Fender Brace is made to help support your front fender/guard. Also helps support and reduce fatigue from constant vibration.

Made from 4mm 5083 structural aluminum plate. If you wanted to carry a small tool bag this would be a perfect product to support the weight and strap the bag to.

Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting.

Ditch the stock ugly plastic sub-fender and install a B&B Off Road Engineering License Plate Holder. Comes with an LED light to keep the license plate lit up.

The stock tail light, blinker and license plate bracket is rather large and cumbersome, to put it politely. The B&B Off Road Engineering unit is simple and tidy and gives you a LED tail and brake light unit, a LED license plate light and turn signal mounts as well.

Installation is easy - remove the stock unit and bolt the new unit in the same location. Off with the old and on with the new in minutes. All necessary hardware included.

License plate holder has been designed to replace the bulky standard assembly with a sturdy, neat unit. The Tail tidy accepts the standard Yamaha blinkers and is supplied with a LED number plate light.

• 3 piece CNC machined from high-quality alloy
• Designed to bolt straight into position with no modification to the bike
• Available in polished or black ppa coated

B&B Off Road Engineering KTM 1290 Bash plate is made from 5mm thick 5083 structural alloy plate. Rear mounts are 5mm stainless steel with a rearward facing lug that rests on the rear frame rail to prevent rotation of the bracket. There are 6 32mm hole in the underside to help flush debris and minimize noise. There is also a rubber damper glued inside to help reduce noise. Bash plate can be fitted with or without genuine KTM crash bars. All necessary mounting hardware for this is supplied.

The ultimate in protection for the bottom of your 650 V-Strom. Constructed from 5mm aluminium 5083 plate. Selected because of its extreme suitability for welding and impact resistance, this material makes a great looking and very strong Bash Plate. This plate extends up far enough to be a great Oil Cooler protector as well. All Bash Plates have a polished finish and have foam or rubber where required.

B&B Off Road's Honda CRF250 Rally bash plate is made from 4mm aluminium 5083 plate. This grade of aluminum is chosen because of its extreme suitability for welding and abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

Bash plate is installed after first removing the lower OEM plastic bash plate/fairing.

This plate will protect the valuable center cases. All skid plates are supplied with the necessary stainless clamps and bolts where possible.

The Honda CRF1000L Twin Dakar Bash plate. Our all new engine protection system is designed to provide all the benefits of a lower crash bar and bash plate in one. It is constructed from 4mm & 5mm 5083 structural plate combined with 20mm heavy wall alloy tubing to form the outer profile. It is mounted in seven locations to make it the most rigid bash plate on the market. It has a narrower profile and fewer snag points than the conventional crash bars. Available in polished or black powder coat.

Fitment notes:

• Will fit with most upper fairing crash bars. Honda Genuine do not fit with bash plate on the standard models.
• At this stage, we do not know what aftermarket headers the bash plate will fit with.
• It has oil drain access points but for a full oil change with the filter, the plate must be removed (10min).
• Requires exhaust system removal for first-time installation only.
• Fits with the centerstand. Fits with SW Motech, Outback Motortek, Hepco and Becker and Altrider Crash bars UPPERS ONLY
• A small modification is required to mount bash plate to adventure sports model. The small bracket attached to the bottom of the crash bars that connect to the genuine skid plate must be removed for clearance. See the additional information link below.

T700 TENERE Bash plate was designed to withstand the harshest Aussie conditions. Bash plate is made from 5mm structural thick alloy plate and designed for maximum protection with minimum bulk.

Easy to mount and remove. Also includes a replaceable polyethylene linkage guard.

• Fully tig welded
• Comes in polished or black PPA coating.
• All hardware for mounting is included.
• 4 Flush fitting mounts, 2 M8 and 2 M6
• Weighs 3.8kg
• Fits with Genuine Centerstand

Fits EURO 4 only

This bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

This plate will protect the valuable center cases. All skid plates are supplied with the necessary stainless clamps and bolts where possible.

This bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

This bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

This bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

This plate will protect the valuable center cases. All skid plates are supplied with the necessary stainless clamps and bolts where possible.

More info coming soon.

bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

This bash plate is made from 5mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

• Fits with  the Genuine Suzuki crash bars
• Designed only to fit with crash bars. Cannot be mounted without the Genuine suzuki crash bars installed

B&B Off Roads KTM 950 Super Enduro bash plate is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

This Australian made bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

Fits with SW Motech & Givi Crash bars.

B&B Off Roads Honda CRF80, CRF100, XR80 & XR100 bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible.

All bash plates have a polished finish and have foam or rubber where required.

This plate will protect the valuable center cases. All skid plates are supplied with the necessary stainless clamps and bolts where possible.

B&B Off Roads Honda CRF50, CRF70, XR50 & XR70 bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible.

All bash plates have a polished finish and have foam or rubber where required.

This plate will protect the valuable center cases. All skid plates are supplied with the necessary stainless clamps and bolts where possible.

B&B has updated this design to fit the 2019 model.

B&B Off Roads Honda CRF125F bash plate is designed to give your mini bikes frame rails & engine casings some added protection. Your engine casings a very vulnerable part of your bike which can be easily damaged from roosted debris, sticks/logs while riding or from simply dropping your bike. 

• Made from 4mm 5083 Structural Plate
• Fully tig welded
• Comes in polished or black PPA coating.
• All hardware for mounting is included.
• Foam insulated to help reduce frame contact/rubbing

B&B Off Roads Yamaha WR450F bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

B&B Off Roads Honda CRF230L bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible.

All bash plates have a polished finish and have foam or rubber where required.

B&B Off Roads KLX230R bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

B&B Off Roads Honda XR150L bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

B & B Off Roads Honda CRF300L bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

The Honda CRF1100 DCT Bash plate is a full coverage Rally style protection for frame rails & lower to mid engine cases. Constructed for more serious off road use in mind, it features multiple additional mount points, paired with a semi double skin 4mm 5083 aluminum Bash plate. All CNC machined and fully tig welded, the side wings are partial double walled for extra stiffness. It also features the addition of a HDPE end plate for the clutch case mated to a rubber puck insert on the plate for additional protection.

Finish Options

• Polished or Black Powdercoat

Whats Included-

• Heavy Duty Bash plate
• Engine Puck/ Bash PLate Puck
• 2 Mild steel mount brackets
• All mounting fasteners

Additional Info-

• Fits with genuine centerstand

B&B Off Roads Kawasaki KLX250 & 300 bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. 

All bash plates are supplied with the necessary stainless clamps and bolts where possible. 

All bash plates have a polished finish and have foam or rubber where required.

These plates are made from 4mm thick 5083 aluminum because the extreme abrasion and impact resistance for the full weight of the bike and the rider. The front portion of the B&B Skid Plate bolts to mounts that are permanently attached to the forward motor mount. This means no more trying to hold clamps in place when you take you skid plate off for oil changes or cleaning. Easy off, easy on. All necessary hardware is included in the kit. The plate has foam or rubber wherever there is contact with the frame.

Choose from a polished finish or a black polymer coating.

The Safari Bash Plate is a bit bigger and more protective than the Big Tour model. Made from the same 5mm 5083 plate, this plate extends further up the front and around the sides of the motor. There is a specific DCT model that wraps up even further to help protect the important parts on the right side. (See last image.)

Fits with the OEM centerstand, but will NOT work with lower engine crash bars. Will work with Upper Crash Bars from SW-MOTECH, Hepco and Becker and OEM Honda units. Remember, all B&B bash plates are quality built and supplied with all necessary hardware and detailed instructions. Foam or rubber is included wherever it is required.

The Big Tour Bashplate from B&B Off Road Engineering is built from 5mm 5083 aluminum plate providing protection from rocks and sticks and other debris. This plate will work with the OEM centerstand and most crashbars.

If you are headed out for miles of back roads and trails, please consider the more protective Safari model. All B&B bash plates are quality built and supplied with all necessary hardware and detailed instructions. Foam or rubber is included wherever it is required.

B&B Eng. has created a true 'Bash Plate' for the mid-sized XT. Wings on the side of the plate deflect debris from the center and side cases. Manufactured from 4mm 5083 aluminum plate which is selected for its extreme suitability for welding, abrasion and impact resistance. Available in a polished finish or a complete covering with a black polymer coating. All necessary stainless clamps and is provided as well as foam or rubber when required.

Protect your frame/paint from scuffs and scratches with frame guards. The DRZ 400 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

Protect your frame/paint from scuffs and scratches with frame guards. The CR 500 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength.

All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

Protect your frame/paint from scuffs and scratches with frame guards. The CR80 & CR85 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

This master cylinder guard is made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All guards are supplied with all necessary mountings and stainless bolts. Made to cover and protect the rear brake master cylinder.

It looks great and is easy to install.

Comes with polished finished.

Australian made, this protector bolts to the stock caliper bracket.

Australian made, this protector bolts to the stock caliper bracket.

B&B Off roads Ktm 950 and 990 adventurer master cylinder guard is made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All guards are supplied with all necessary mountings and stainless bolts. Made to cover and protects the rear brake master cylinder it looks great and is easy to install. Comes with polished finished.

B & B Off Roads Kawasaki KLR 650 master cylinder guard is made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All guards are supplied with all necessary mountings and stainless bolts. Made to cover and protects the rear brake master cylinder it looks great and is easy to install. Choose between polished or black polymer finish.

Superior strength and protection against larger debri as well as small rocks etc.

If purchasing bash plate you will not need to purchase, the oil cooler guard is already incorporated into the bash plate.

This Australian made radiator stone guard is machined from 4mm aluminium 5083 plate. The extra thickness of material provides superior strength and protection against larger debri as well as small rocks etc. Radiator guards can be fitted in approx ½ hr or less using basic tools.

All radiator guard mounting hardware is supplied where necessary.

B&B Off Road Engineering provides the most advanced radiator protection system available.

B&B RADIATOR GUARDS FEATURE -

1. Maximum side and front impact protection-Using a combination of CNC machined 6000 series 3 dimensional aluminum extrusion and 5000 series alloy plate we have created a system to protect your radiators from virtually every direction

2. Maximum roost and debris protection- Due to the angle fin design in our radiator guards there is very little of the radiator core and veins that are directly exposed to roost, debris and trail side sticks

3. Maximum airflow -B & B Off Roads unique aluminum front louver panel constructed from high strength extrusion allows 3 dimensional fins to be incorporated into the design to mimic the airflow characteristics of the genuine plastic radiator fins

4. Removable finned louver panel- Front panel only requires a few bolts to be loosened to allow for easy removal for cleaning of the radiator

5. Integrated modular construction- Three piece modular construction allows for greater design flexibility eliminating the compromises inherent with one piece designs

6. Easy fitment no mods required- Radiator guards can be fitted in approx ½ hour using basic tools

7. All parts available individually- If you damage any part of the radiator guards our design allows you to purchase only what you require

This modular design utilizes two precisely machined 2.5mm thick alloy sheets. This unique construction offers two key benefits:

Maximum Airflow: The design allows for exceptional airflow, ensuring your engine stays cool even on the most demanding rides.
Superior Protection: By minimizing the visible radiator core area from the front, the guard deflects stones, dirt, and debris away from the delicate fins.

Constructed from high-quality alloy, this radiator guard is lightweight yet incredibly strong, providing lasting protection for your adventure bike.

Available in two finishes

Brushed Silver: A classic, polished look that complements your Transalp’s style.
Low Luster Textured Powdercoat: This new finish offers a stealthy and durable option for a truly off-road-ready aesthetic.
Simple Installation: This radiator guard mounts easily using existing points on your XL750 Transalp, requiring no modifications for a hassle-free upgrade.

Invest in peace of mind. This radiator guard offers a significant layer of defense against common road hazards, letting you explore with confidence. Order yours today and experience the difference!

B&B Off Road Engineering Radiator Guards are much stronger than the plastic OEM guards. Made from extruded aluminum and then CNC machined, these guards us a louver design like those of a modern motocross machine which provides maximum protection while allowing maximum airflow through the radiator for excellent cooling.

With the mounting system for these guards, they are easily and quickly removed if you need to get in for a good cleaning. Remove four easily accessible bolts and the guards are out of the way.

WILL NOT FIT WITH SW-MOTECH UPPER TANK BARS! Modifications will be needed to fit with the crossbar of the crash bar that runs in front of the radiator.

CNC machined from 6mm aluminum plate case saver, with a 4mm aluminum front sprocket cover.

CNC machined from 2.5mm marine grade aluminum- replace the stock plastic guard

A CNC machined Chain Guide that is considerably stronger than the stock plastic unit.

High Quality chain. Will need to be cut to fit your sprocket combination.

• Computer-designed to achieve ultimate strength at minimum weight
• JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
• Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
• Sprockets are heat-treated and bead-blasted to reduce material surface tension
• Unless noted, front sprockets are made with C45 steel and SCM415 chromoly steel alloy; rear sprockets made with top-quality-grade C45 high-carbon steel

JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. Made exclusively from the finest Japanese 545C high carbon steel

T7 Solo Carry rack has been designed predominantly for the solo rider to keep loads as forward and low as possible. The plate has multiple attachment points making easy to tie down bags.

The plate is pre-drilled for mounting systems for both Givi monokey and Rotopax. The rack is light in weight only weighing 2.3kg.

• Fits with standard seat only. Will not fit with Rally seat
• Fully tig welded
• Comes in polished or black PPA coating.
• All hardware for mounting is included.
• Made from 5mm thick cnc machined plate
• 420mm x 260mm surface area
• Slim design
• Compact and rigid
• 4 Bolt removal

CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the stock rack. Attaches directly to the stock rack with four screws that are included. Available in either polished aluminum or a black polymer coating.

These plates are pre-drilled making installation of a RotoPax mount quick and easy.

Dimensions

• Total Length: Approx 35cm / Flat Surface: Approx 35cm 
• Total Width: Approx 39cm /  Flat Surface: Approx 32cm

CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the stock rack. Attaches directly to the stock rack with four screws that are included. Available in either polished aluminum or a black polymer coating.

These plates are pre-drilled making installation of a RotoPax mount quick and easy.

Dimensions

• Total Length: Approx 35cm / Flat Surface: Approx 35cm 
• Total Width: Approx 39cm /  Flat Surface: Approx 32cm

This luggage rack is made from 5mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

Luggage plates will come with pre-drilled holes to suit rotopax mount. On request luggage plates can be pre-drilled to suit Givi top case mounting hardware.

DIMENSIONS

• Total Length: Approx 33cm
• Total Width: Approx 33cm closest to seat, approx 27cm at rear

Our latest crf230f rack is designed for superior strength in mind for use in commercial and rural conditions. The main part of the rack in constructed from mild steel which connects to the subframe in 3 points and is designed to stiffen the assembly to carry a decent pay load. The top plate of the rack is 5mm aluminum with multiple tie down points and predrilled for rotopax/ fluid tanks which are available separate.

Luggage Plate:

• Total Width Approx 29cm
• Total Length Approx 33cm

Carry Rack:

• Total Width Approx 15cm
• Total Length Approx 20cm

Carry Rack and Luggage Plate Total Length Approx 54cm

B&B Off Road's KLR650 Luggage Rack is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

DIMENSIONS

• Total Length: Approx 42cm
• Total Width: Approx 40cm

Our KTM 950 Super Enduro Luggage Rack is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

DIMENSIONS

• Total Width Approx 35cm, Width of flat surface approx 31cm
• Length of flat surface approx 30cm

Our KTM 950 Super Enduro Luggage Rack is CNC machined from 5mm aluminum 5083 structural plate. 

All of our Carry racks & Luggage plate racks are supplied with the necessary mounting hardware needed for fitment.

• Available in Polished or Black
• Predrilled Rotopax mount holes (not pictured, more to come)

DIMENSIONS

• 250mm wide x 239mm long

B&B Off Road's Honda Africa Twin Adventure Sport Big tour combo Luggage Rack has a two-piece main luggage plate with an added extension plate that mounts directly to the main rear rack and grab rails. Requires no modification for mounting.

Main luggage, adapter mounting plate and extension are all made from 5mm aluminum 5083 structural plate.

Very quick installation and can be done in a matter of minutes. The adapter plate is threaded for an easy install and removal of luggage plate which also includes mounting locations of our extension plate. Extension plate has some cnc machined billet clamps used for mounting.

Extension plates are great for those wanting to carry a larger load for a weekend trip or even to distribute some of the weight further forward

All the necessary bolts and brackets are supplied for mounting.

Rotopax and Givi Monokey holes are pre-drilled to suit the required mounts.

Total Width Maxi Plate Approx 45cm, Width of flat surface Maxi Plate approx 40cm

Total Length Approx 33cm

The Honda Maxi Luggage Rack and extension is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

DIMENSIONS

Maxi Plate:
Total Width Approx 45cm, Width of flat surface approx 40cm

Total Length Approx 33cm, Length of flat surface approx 33cm

Extension Plate :

Total Width: Extension Plate Approx 46cm

  Will not fit adventure sports model. Please see other listing.

B&B Off Road's Honda Africa Twin Adventure Sport Big tour combo Luggage Rack has a two-piece main luggage plate with an added extension plate that mounts directly to the main rear rack and grab rails. Requires no modification for mounting.

Main luggage, adapter mounting plate and extension are all made from 5mm aluminum 5083 structural plate.

Very quick installation and can be done in a matter of minutes. The adapter plate is threaded for an easy install and removal of luggage plate which also includes mounting locations of their extension plate. Extension plate has some CNC machined billet clamps used for mounting.

Extension plates are great for those wanting to carry a larger load for a weekend trip or even to distribute some of the weight further forward.

All the necessary bolts and brackets are supplied for mounting.

Rotopax holes are pre-drilled to suit the required mounts.

DIMENSIONS

Mini Plate:

• Total Width Mini Plate Approx 32cm
• Total Length Approx 28cm

Extension Plate/Pillion

• Total Length Approx 27cm
• Width Approx 39cm

Total Length Including Mini and Extension Plate: Approx 55cm

A sturdy and compact tail rack formed from 1 piece of structural 5mm thick alloy plate. Mounting utilizes the rear factory mount and their hidden sub-frame mount bracket.

Please note a small notch on the inner black plastic guard is needed to mount bracket.

The rack comes pre-threaded for optional luggage plate attachment. 

• Comes in polished or black PPA coating.
• All hardware for mounting is included.
• Made from 5mm thick cnc machined plate
• Weighs 1kg

Designed to make your compact rack even more versatile for riders who need a larger luggage platform. 

• Comes in polished or black PPA coating.
• All hardware for mounting is included.
• Made from 5mm thick cnc machined plate
• Weighs 1kg
• Multiple attachments points 
• Pre drilled for Givi monokey mount system
• Pre drilled for roto pax fluid containers
• This listing is for the Rear luggage plate only
• Dimensions 25cm x 26cm flat surface 
• Does not include Pillion handles or base tail rack. Please see other listings for these items

The CRF300L & rally rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.

DIMENSIONS

Length: Approx 35cm - Total Length: Approx 42cm

Total Width Flat Surface: Approx 17cm

ADD-ON

Pillion handles designed for quick and easy removal. 

• Pillion Handles for passenger
• Made from 12mm Solid round Bar
• Can also be utilized as tie rails for larger bags 
• This listing is for rear Pillion handles only does not include base tail rack or luggage plate. Please see other listings.

B&B Off Road's Honda Africa Twin Adventure Sport Mini and Maxi Luggage Racks are a two-piece design that requires no modification for mounting.

Both the luggage plate and adapter mounting plate are made from 5mm aluminum 5083 structural plate.

Very quick installation and can be done in a matter of minutes. The adapter plate is threaded for an easy install and removal of luggage plate which also includes mounting locations of their extension plate (sold separate).

All the necessary bolts and brackets are supplied for mounting.

Rotopax and Givi Monokey are pre-drilled to suit the required mounts.

The B&B Off Road Engineering rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.

DIMENSIONS

Width Flat Surface Approx 18cm

Length Approx 33cm – Total Length Approx 45cm

Please Note- To fit rack, two holes need to be drilled into the rear guard. The position of holes are already marked on genuine Yamaha guard so no template is required.

The Honda Maxi Luggage Rack and extension is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

DIMENSIONS

Maxi Plate:

• Total Length: Approx 55cm / Centre Surface: Approx 50cm 
• Total Width: Extension Plate Approx 46cm /  Mini Plate: Approx 33cm

  Will not fit adventure sports model. Please see other listing.

Increased Capacity & Convenience:
Mounts to Existing Carrier: This plate seamlessly integrates with your stock rear carrier, providing a larger, more usable surface for your luggage.
Abundant Tie-Down Points: Numerous pre-drilled holes offer ample options for securing your cargo with straps and bungee cords. Chamfered tie-down slots- Top & Bottom.

Built to Last:
Durable Construction: Crafted from robust 5mm 5083 aluminum plate, this luggage plate can handle the weight of your gear with ease.

Simple Installation:
Quick & Easy Setup: Installs in just minutes using the included bolts and spacers, requiring no modifications to your motorcycle.

Versatility & Style:
Rotopax & Givi Monokey Compatibility: Pre-drilled holes allow for the easy installation of Rotopax mounting systems and Givi Monokey top cases.
Choice of Finishes: Select between a polished finish or a new low-luster textured powdercoat to complement your Transalp’s aesthetics.

The B&B Off Road Mini Luggage Plate is the perfect solution for riders seeking to maximise their Honda XL750 Transalp’s luggage capacity without compromising on convenience or style.

Whats Included:

• Aluminium Luggage Plate
• Aluminium luggage plate joiner
• Aluminium luggage extension plate
• All mounting Hardware
• Rotopax and overland are pre-drilled to suit the required mounts.
• Givi Monokey pre-drilled to suit the required mounts

Expand your cargo options and conquer longer journeys with the B&B Off Road Maxi Luggage Plate, custom-designed for your Honda XL750 Transalp (2022).

Increased Capacity & Convenience:
Mounts to Existing Carrier: This plate seamlessly integrates with your stock rear carrier, providing a larger, more usable surface for your luggage.
Abundant Tie-Down Points: Numerous pre-drilled holes offer ample options for securing your cargo with straps and bungee cords. Chamfered tie-down slots- Top & Bottom.

Built to Last:
Durable Construction: Crafted from robust 5mm 5083 aluminum plate, this luggage plate can handle the weight of your gear with ease.

Simple Installation:
Quick & Easy Setup: Installs in just minutes using the included bolts and spacers, requiring no modifications to your motorcycle.

Versatility & Style:
Rotopax & Givi Monokey Compatibility: Pre-drilled holes allow for the easy installation of Rotopax mounting systems and Givi Monokey top cases.
 

Choice of Finishes: Select between a polished finish or a new low-luster textured powdercoat to complement your Transalp’s aesthetics.

The B&B Off Road Maxi Luggage Plate is the perfect solution for riders seeking to maximize their Honda XL750 Transalp’s luggage capacity without compromising on convenience or style.

Expand your cargo options and conquer longer journeys with the B&B Off Road Mini Luggage Plate, custom-designed for your Honda XL750 Transalp (2022).

Increased Capacity & Convenience:
Mounts to Existing Carrier: This plate seamlessly integrates with your stock rear carrier, providing a larger, more usable surface for your luggage.
Abundant Tie-Down Points: Numerous pre-drilled holes offer ample options for securing your cargo with straps and bungee cords. Chamfered tie-down slots- Top & Bottom.

Built to Last:
Durable Construction: Crafted from robust 5mm 5083 aluminum plate, this luggage plate can handle the weight of your gear with ease.

Simple Installation:
Quick & Easy Setup: Installs in just minutes using the included bolts and spacers, requiring no modifications to your motorcycle.

Versatility & Style:
Rotopax & Givi Monokey Compatibility: Pre-drilled holes allow for the easy installation of Rotopax mounting systems and Givi Monokey top cases.
Choice of Finishes: Select between a polished finish or a new low-luster textured powdercoat to complement your Transalp’s aesthetics.

The B&B Off Road Mini Luggage Plate is the perfect solution for riders seeking to maximize their Honda XL750 Transalp’s luggage capacity without compromising on convenience or style.

Made 'down unda' by B&B Off Road Engineering in Australia, these racks are CNC machined from 5mm 5083 aluminum plate with lots of slots around the edge to attach your RokStraps or other tie-down devices. The plate attaches directly to the CRF rear frame with four screws that are included.

There are four options for this plate, two sizes (Mini and Maxi) and two colors each (Polished and Black Polymer coating). The Maxi Plate is 18" wide at the seat, 13" long and 8.5" wide at back. The Mini Plate is 12 3/4" wide at the seat, 11" long and 9 1/4" wide at the back.

The Big Tour Extension optional add on below is a forward extension for the Luggage Plates shown above. CNC machined from the same 5mm 5083 aluminium plate, this covers the rear portion of your seat and turns that area into a solid platform for packing more stuff for your RTW adventure.

This beautiful polished rear carry rack from B&B Eng. is made from aluminum tubing and 4mm 5083 plate. 5083 is used because of its suitability for welding and high level of abrasion and impact resistance. Kit includes all the necessary stainless clamps and bolts. With the roundness and strength of the tubing supports, it makes a great grab handle when you need to lift the rear of the motorcycle.

The Big Tour Extension is a forward extension for the Luggage Plates.

CNC machined from the same 5mm 5083 aluminium plate, this covers the rear portion of your seat and turns that area into a solid platform for packing more stuff for your RTW adventure.

You can combine it with either the Maxi or Mini rack and then get the combo in either a Polished finish or a Black Polymer coating.

*Extension plate only, mini / maxi plate sold separate, or in complete set.

This beautiful polished rear carry rack from B&B Eng. is made from aluminum tubing and 4mm 5083 plate. 5083 is used because of its suitability for welding and high level of abrasion and impact resistance. Kit includes all the necessary stainless clamps and bolts. With the roundness and strength of the tubing supports, it makes a great grab handle when you need to lift the rear of the motorcycle.

Their baffle was designed to replace the stock insert. The baffle produces a nice note compared to the de-restricted stock version and dyno test results showed an increase on 2 hp up top.

A noise test on the insert was conducted at the EPA Victoria Vehicle Test Station at Macleod under controlled conditions with Class 1 meters.

Some extra details:

1. The ADR test is conducted at an engine speed which is 50% of the engine rpm at which the engine develops maximum power. However, this engine speed is determined when the bike is in restricted form, with a throttle restrictor that stops the throttle being fully opened. This is why the ADR engine test speeds are so low. However, they are the engine speeds used to determine compliance.
2. On the ADR test, the B&B tip was over the signature noise emission, but a tolerance of 5 dB(A) is allowed before prosecution would be initiated. With this tolerance, the insert would not be prosecuted as it is just 4 dB(A) over the signature.
3. When tested with the standard OEM tips (as fitted when delivered from Suzuki Australia), the Suzuki came in at 95 dB(A) for the ADR test

Does not contain a spark arrestor. Check local laws on spark arrestors before purchase.

B&B Off roads KTM 950 Super Enduro shock reservoir heat shield is made from 2mm aluminum 5052 plate. The heat shield is design to create a barrier between your riding gear and the exhaust/muffler preventing heat transfer and burns to your protective gear.

B&B Off roads KTM 950 Super Enduro Heat shield is made from 2mm aluminum 5052 plate. The heat shield is design to create a barrier between your riding gear and the exhaust/muffler preventing heat transfer and burns to your protective gear.

X3 EVO represents the off-road evolution: LeoVince has combined all its experience in the off-road world with cutting-edge materials and Italian design, enhancing freedom in its purest form.

The X3 EVO body is made of AISI 304 stainless steel with TIG welds handcrafted by specialized operators, to guarantee long-lasting performance. X3 EVO will allow you to face the most extreme environments and conditions because it does not fear water or mud, nor wear over time.

The LV logo is their tribute to a motorcycle culture that we have loved for 70 years and is laser etched on the body of the exhaust: it is as endless as their passion.

They manufacture the end cap in 100% real carbon, with their special 2x2 twill carbon fiber, specifically designed to resist high temperatures and make the X3 EVO even lighter.

The matte clear coating, in addition to enhancing the carbon texture, protects the end cap from wear and UV rays, keeping the X3 EVO always in a perfect shape.

The sound of X3 EVO is already unmistakable at low revs. X3 EVO has a direct interior, specially conceived to channel the exhaust gas in an optimal way, to unleash a deep sound, giving a new voice to your bike.

The X3 EVO's Spark arrester has been tested and approved by the United States Forest Service and is essential for off-road riding in compliance with regulations, with more peace of mind, more respect for the environment and more fun.

radiator stone guard is machined from 4mm aluminium 5083 plate. The extra thickness of material provides superior strength and protection against larger debri as well as small rocks etc. Radiator guards can be fitted in approx ½ hr or less using basic tools. All radiator guard mounting hardware is supplied where necessary.

B&B Off Roads KTM 950 & 990 Adventurer bash plate is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

The KTM 950 and 990 adventurer luggage Rack is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

DIMENSIONS

• Total Width Approx 35cm, Width of flat surface approx 31cm
• Length of flat surface approx 30cm

• Made from 4mm 5083 Structural Plate
• Fully tig welded 
• Comes in polished or black PPA coating. 
• All hardware for mounting is included.
• Installation guide included

Note - Drilling of the rear guard is required for installation.

Remove the bulky stock number plate holder with our slim design- comes with LED number plate light.

• Quick and easy install
• Mounting hardware supplied
• Comes with clear LED tail, brake & number plate light
• No mods required for installation
• Available in polished or black PPA coating.
• Pre drilled to suit Australian licence plate

*Please Note:  Brake light does not come with necessary/factory connectors. Some cutting, crimping, soldering of wires may be required for connection.

Sharpen Your Yamaha WR250R’s Look with B&B Off Road’s Tail Tidy

Give your Yamaha WR250R (2008-2021) a shot of attitude with B&B Off Road’s premium tail tidy! This innovative replacement ditches the bulky stock fender for a sleek and stylish design that elevates your bike’s aesthetics without compromising functionality.

Clean Lines, Easy Installation:

This tail tidy boasts a streamlined design that sheds unnecessary weight and bulk, instantly transforming your WR250R’s rear end. The straightforward installation utilizes existing mounting points for a hassle-free experience – get ready to hit the road (or trail) in no time.

Choose Your Finish:

Personalise your tail tidy to match your WR250R’s personality. Opt for a gleaming polished finish for a bold statement, or choose the classic black PPA-Gloss for a refined look. The brand new, low-lustre textured black powder coat (PC) offers a stealthy aesthetic for a more aggressive stance.

Unleash Your WR250R’s Potential:

This tail tidy doesn’t just enhance your bike’s visuals. The reduced weight contributes to improved performance, letting your WR250R handle even better. With a cleaner and more streamlined rear end, your adventure awaits in style.

Upgrade your Yamaha WR250R today! Order your B&B Off Road Tail Tidy and experience the perfect blend of functionality and sharp design.

An aluminum Light Mount for your bike. Put whatever light you like up front for more light as well as great daytime visibility to other vehicles. Win-win situation. Choose the Single Mount or Double Mount.

The stock tail light, blinker and license plate bracket is rather large and cumbersome, to put it politely. The B&B Off Road Engineering unit is simple and tidy.

Installation is easy - remove the stock unit and bolt the new unit in the same location. Off with the old and on with the new in minutes. All necessary hardware included.

Machined from high grade alloy plate and designed to be a simple install to help prevent your pride and joy from hitting the deck on soft ground.

The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.

• DOT approved, tube type
• 4-ply rating
• All sizes designed for front or rear fitment

From Shinko Tires, the 705 Series are DOT approved Dual Sport tires designed for 75% street and 25% trail riding. A versatile tread pattern provides excellent wet and dry weather adhesion and the compound resists tearing while riding off-road. "R" in size denotes a radial tire.

The Shinko 244 is a very popular tube-type upgrade for the front tire on the TW200 or the VanVan. DOT approval coupled with excellent performance both on and off-road make this tire a winner!

The 244 Series dual purpose street and trail tire is designed to be equally at home on dirt or pavement.

• Adventure Trail
• Dual purpose street and trail design
• Designed to be equally at home on dirt and pavement
• DOT approved

Available in 5.10-18 (69P load / speed rating) and 4.60-18 (69S load / speed rating).

Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.

Key Features:

• High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.

• Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.

• Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.

• Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.

• Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction
• Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals
• Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action
• Lower Stiction, Longer Life! It doesn’t get any better than this!
• Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance

• Includes all necessary parts to rebuild the OEM fuel pump module
• Restore lost performance or non-functioning fuel pump with this economical solution
• Kit comes ready for plug-and-play installation