The cush hub (sprocket carrier) bearing leads a tough life. This is especially true if your cush rubbers get old and soft. They can allow the chain to pull the cush hub sideways putting a twisting load on the bearing. If there's any question about the condition of your bearing replace it now with this double sealed bearing and quality seal.
This kit will replace your stock sprocket bolts, nuts and keepers with new hardware.
Many aftermarket sprockets are thinner where they bolt to the wheel and the threads on the stock bolts do not allow these sprockets to be tightened down all the way. These grade 10.9 bolts will alleviate that problem. They are the same length as the stock ones, but the threaded area is longer allowing stock sprockets or aftermarket sprockets to be securely tightened down.
The bolt keepers are genuine Yamaha replacement parts to ensure an accurate fit. It's a perfect upgrade if your keepers have been removed too many times.
This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.
CNC laser cut from 1/8"5052 aluminum then black powder coated and the logo laser etched in place with the V-Strom 650 logo to really set it off. The laser etched logo will not wear off like a vinyl or screen printed graphic.
Heavier gauge aluminum than other aftermarket guards and better coverage than the stock guard. It also will not crack at the stress points. Uses the stock mounting screws.
B&B fired up the CNC equipment for another beauty, a Front Sprocket Case Saver. A great investment the 6mm aluminum base will protect your engine cases should your chain ever break or derail. On top of that is a 4mm piece to keep your pants and other things out of the chain as well. This replaces the stock cover over the countershaft sprocket.
If you have a 16t front sprocket, mounting modification may be needed to fit.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
Give your Honda the ultimate protection with B&B Off Road’s heavy-duty chain guard. This premium upgrade replaces the stock plastic guard, notorious for bending and breaking on tough terrain.
Crafted for Unrelenting Performance:
Precision-machined from robust 2.5mm marine-grade aluminium, this chain guard delivers unparalleled strength and durability. Say goodbye to worries about trail debris or rogue rocks damaging your chain – this guard stands strong against anything you throw at it.
Lightweight Design, Maximum Protection:
Despite its impressive strength, the chain guard is engineered to be lightweight, minimising any additional weight on your bike. This meticulous design ensures optimal performance without sacrificing protection.
A Perfect Fit:
This B&B Off Road chain guard seamlessly integrates with your Honda CRF, eliminating any installation hassles. The precise CNC machining guarantees a perfect fit for each compatible model.
Invest in Peace of Mind:
Protect your chain, a vital component of your motorcycle’s drivetrain. By preventing damage from debris and impacts, this chain guard minimises the risk of breakdowns and costly repairs. Hit the trails with confidence, knowing your CRF is shielded for the long haul.
Two parts in one. Not just a cover over the countershaft sprocket, but also a case saver as well! Should you ever throw a chain, this will keep it from going into the engine cases and causing extensive and expensive damage.
Chain guards experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.
Universal fit. May require additional adjustment or modification.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Universal fit. May require additional adjustment or modification.
PBR = press, break, rivet
Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
All components conveniently store on tool when not in use
All steel construction with heat-treated components for strength and durability
May be supported in a vise or held with included handle
Great for the professional technician or DIY mechanic
Compact and light enough to carry in a tool bag for trail-side repairs
Universal fit. May require additional adjustment or modification.
Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.
Even and Accurate Lubrication: Their patented dispenser features exit holes that align with your chain's link plates, ensuring the areas that need it most get it.
Minimize Over-spray: Keep your motorcycle clean and free of messy chain lube.
Reduce Waste: No more over-lubing your chain. Their patented dispenser enhances the efficiency of your lubricant use.
Rotatable Dispenser: Allows you to adjust your hand positioning. Ideal for bike's with chain guards.
Durable: Constructed from glass-filled nylon, Oinker is strong, durable, and resistant to chemicals.
Universal Compatibility: Fits any standard can of lubricant.
*For cans with an attached smart straw, you will need to replace it with the included nozzle
What's Included:
1 Chain Oiler
3 aerosol straws
3 replacement nozzle to be used only on cans that have attached straws.
Universal fit. May require additional adjustment or modification.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Universal fit. May require additional adjustment or modification.
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
High Quality chain. Will need to be cut to fit your sprocket combination.
Lower friction and longer life. X-rings have twice the sealing ability as compared to o-rings. They do a better job of keeping the lube in the links and the dirt out. DID VX chains have a reputation for being the best chain you can buy for dual sport riding. DID VX chains come with rivet type master links.
Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.
Shield your bike’s vital drivetrain components with B&B Off Road’s heavy-duty front sprocket case saver. This premium guard, CNC-machined from high-strength 6mm aluminum plate, offers unparalleled protection against rocks, impacts, and other off-road hazards.
Uncompromising Strength, Precision Fit: Engineered for maximum durability, this case saver boasts a 6mm main body crafted from 5083 structural aluminum – a material renowned for its resilience. Complementing this robust core is a 4mm thick front sprocket cover, ensuring comprehensive protection for your drivetrain.
Designed for Flawless Performance: CNC machining guarantees a precise fit for both Suzuki DRZ400 (2000+) and Kawasaki KLX400 (2000+) models. This ensures seamless integration with your bike, eliminating concerns about interference or compatibility issues.
Peace of Mind on Every Ride: Whether you’re navigating technical single tracks or powering through dusty plains, this case saver offers the confidence to push your limits. By safeguarding your front sprocket and surrounding components, it minimizes the risk of costly repairs and keeps you on the trail.
This heavy duty DRZ400 chain guard is made of laser cut 1/8” aluminum and finished in textured black powder coating. The formed flange helps keep chain grime off the rear tire.
Many riders choose to convert over from the stock 525 to a 520 chain. Besides being lighter and less expensive, a 520 chain is more readily available as well as having more sprocket size options.
Quality steel sprockets and 525 O-Ring chain. 525 chains come in 120 link length and will have to be cut down to fit. They also come with rivet type master links. Clip type master links are available below. Single sprockets and chains are also available below.
Chain sliders may undergo degradation over time due to the friction produced by the chain's movement. Restore optimal performance by utilizing this authentic Yamaha component.
Chain guides are subject to wear over time due to friction produced by chain movement. To restore optimal performance, replace them with this authentic Yamaha component.
Fully wraps the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction. Saves expensive engine cases.
Fully wraps the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction. Saves expensive engine cases.
Fully encloses the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction and noise. Saves expensive engine cases.
A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.
A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.
Chain slippers undergo degradation over time due to friction associated with the chain's movement. To maintain optimal operational performance, it is advised to replace worn components with authentic Honda parts.
Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.
Chain sliders undergo performance degradation over time due to the friction experienced by the chain. To maintain optimal functionality, it is recommended to replace worn components with genuine Honda parts.
Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.
Savvy DR650 owners will remove the upper chain roller. You can use this stainless steel button head screw to plug the threaded hole. Suzuki did not make the upper roller mount strong enough. If you don't remove it yourself the chain will likely do it for you - along with a chunk of metal out of the frame.
Reduce the friction dragging down your drivetrain. This chain roller is made from Delrin®, it's self-lubricating and a significant improvement over stock.
Does not use a bearing but rides directly on the frame boss. There is no mounting hardware included.
The Moose Racing is a quality chain roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.
Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.
OEM Suzuki seal retainer for the DR650. Simple insurance against your countershaft seal popping out of its bore.
This is not a common problem but for those folks who have had the seal come out it has proven to be quite difficult to get it to stay in place. This steel retainer eliminates any possibility of the seal coming out and ruining your day by coating your rear tire with oil.
Replacement retainer if yours is worn out or lost. This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).
This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.
All sizes of new FRITZCO sprockets come with a quick change retainer included, this is only a replacement.
This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.
The stock sprocket retainer will rub the chain when it is used with 13 and 14 tooth sprockets.
We have our own sprocket retainer laser cut from 13 gauge stainless steel. This retainer works with all 3-hole 13T, 14T, 15T and 16T DR650 countershaft sprockets.
This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).
This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.
Designed for OFF ROAD USE with the thought in mind that you can ride to your favorite off road spot using a 15 or 16 tooth sprocket and larger than stock rear sprocket. Then quickly change to the 13 tooth and enjoy the ripping torque provided by the huge amount of reduction the 13 tooth offers. Making the XRL much better in the technical stuff. You will really be surprised how much better a big bike like an XRL handles off road with low gearing.
This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.
FRITZCO front sprockets are a straight up no hassle installation. Their sprockets are machined from alloy steel that in every way is comparable to OEM Yamaha and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Yamaha output shaft and longest chain wear life possible.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
Black hard anodized alloy sprocket. Machined sprockets made from 7075 T651 aluminum reduces distortion and provides optimal thickness, to extend sprocket and chain life.
FRITZCO front sprockets are a straight up no hassle installation. Their sprockets are machined from alloy steel that in every way is comparable to OEM Yamaha and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Yamaha output shaft and longest chain wear life possible.
Quality steel sprockets and EK SROZ2 525 O-Ring chain. Available in gear ratio choices from - 13/42 to 15/46. EK SROZ2 525 chains come in 120 link length and may have to be cut down to fit. They also come with rivet type master links. Clip type links are available below.
13 and 14 Tooth sprockets require a smaller retainer
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
Computer-designed to achieve ultimate strength at minimum weight
JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
Sprockets are heat-treated and bead-blasted to reduce material surface tension
Unless noted, front sprockets are made with C45 steel and SCM415 chromoly steel alloy; rear sprockets made with top-quality-grade C45 high-carbon steel
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Computer-designed to achieve ultimate strength at minimum weight
JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
Sprockets are heat-treated and bead-blasted to reduce material surface tension
Unless noted, front sprockets are made with C45 steel and SCM415 chromoly steel alloy; rear sprockets made with top-quality-grade C45 high-carbon steel
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
