ProCycle currently has reduced staffing due to our state governor’s policies. Orders will be processed as efficiently as possible. Your patience is appreciated.

Odds & Ends

Closeout, obsolete, 'Scratch & Dent', good used, etc.

Model

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

This line is black with silver fitting, brand new in packaging with all hardware included.

$59.95

The ProCycle seat was designed for both comfort and function. Our seat is built with a premium denser foam for those long days in the saddle also giving you freedom to move while standing.

  • Wide and firm saddle adds comfort on long rides
  • Narrowing taper up front allows room for knees when standing
  • The vinyl weave pattern allows airflow between you and the seat
  • Provides grip down the sides allowing you to hold on with your knees
Thumbnail

This is a standard seat that has a couple of stretch/puncture marks in the vinyl shown in the second picture.  Sold As is.

$279.95

CALL FOR SPECIAL PRICING, LAST SET IN STOCK.

This is for a complete set of spoke wheels for the 2nd generation SV650, custom built!

The wheels shown are built with a gold anodized RAD hub, black Sun rims and special heat-treated stainless steel spokes that give them a fantastic multi-colored look. These hubs use stock rotors and sprockets.

Will use your Cush Drive / Sprocket Carrier, Sprocket and Brake Rotor.

  • Gold billet alloy hubs with bearings and seals
  • Sun 3.5"x17" front rim
  • Sun 4.25"x17" rear rim
  • Buchanan's heat-treated stainless steel spokes
$1,699.00
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Decompression Plug, ADA Racing

YZ450F '98 - '05 YZ250F '98 - '05 YZ400F '98 - '05 YZ426F '98 - '05 WR250F '98 - '05 WR450F '98 - '05 YFZ450 '04 - '04

Replaces the stock rubber decompression plug in the Yamaha cylinder head that can be prone to blowing out. This billet aluminum one comes with an o-ring and can't pop out like the stock rubber one. Fits: 1998-2005 YZ250F, YZ400F, YZ426F, YZ450F, WR250F, WR450F, and 2004 YFZ 450. Installation is easy, just remove the set screw and pop out the stock rubber plug, then install the new billet plug and re-install the set screw.

$13.95
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Made in USA

Reeds, Boyesen Pro Series

YZ250 '96 - '96 WR250 '96 - '96

Boyesen Pro Series dual-stage reeds combine a carbon-fiber top reed with a fiberglass bottom reed for unrivaled performance. The Pro Series Reeds are more responsive than our traditional Power Reeds. The carbon-fiber top reed has excellent response characteristics that provides even quicker acceleration, stronger throttle response, and more over-rev than our standard Power Reeds. The fiberglass bottom reed provides stability and longer reed life.

$64.95
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Throttle Tube "Tamer", G2 Ergonomics

V-Strom (DL1000) '02 - '12 V-Strom (DL650) '04 - '06 SV1000 '03 - '07
  • Even out the abrupt initial power delivery to eliminate throttle snap that's especially evident with modern EFI bikes
  • Introduce a non-linear ratio between hand throttle and the carb or throttle body opening
  • Throttle cam's radius is reduced initially, which requires the rider to rotate the throttle slightly further to get the same opening position as stock; the radius increases after half-throttle to keep the full-throttle position at or near stock
  • Include a 400 throttle cam and a machined billet aluminum throttle tube with a knurled surface
Thumbnail

Only one available, discontinued item.

$69.95