Engine

Need to remove your clutch assembly to get at that dreaded neutral safety switch? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

Bottom line, if you have to hold your clutch hub to remove it, there is no better way to do it.

This tool helps ease the pain of accessing the neutral safety switch. This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub.

Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut a breeze, and minimizes the likelihood of damaging the clutch hub.

Convenient tool to hold the clutch basket when servicing your clutch

This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub.

Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut a breeze, and minimizes the likelihood of damaging the clutch hub.

Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.

• Features 8mm spanner pins
• Jaws open up to 5 inches wide
• Recommended for square tooth style clutch hubs
• Not recommended for v-groove or half round style clutch hubs

Special tool to remove the flywheel from the end of the crankshaft.

This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.

• Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
• Knurled knob on adjuster drivers ensure a precise and secure grip
• Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw

Set includes:

• (1) 10mm steel socket wrench
• (1) 3mm square tappet adjuster

Special tool to remove the flywheel from the end of the crankshaft.

A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°

• Contains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)
• Can be used to install and adjust timing of any cam
• Wooden carrying case

You have to pull the rotor off the crank of your KLR to access the doohickey. The offset in this factory Kawasaki wrench makes that very easy. It is very difficult to get a standard wrench to hold the crank to get the flywheel/rotor off.

Special tool to remove the flywheel/rotor from the end of the crankshaft. You have to remove the flywheel/rotor to upgrade the doohickey.

Two feeler gauges with angled ends to make checking the clearances easier. Stock valve clearances are .004" intake and .008" exhaust (.10mm in. and .20mm exh.)

For adjusting valve clearance on twin cam models. Holds valve spring collar down so adjusting pads can be removed. From Motion Pro, made from hardened alloy steel.

Getting ready to adjust your valves? Here is a set of feeler gauges to make the job a little easier. One tool has .002" & .003" gauges the other has .004" & .005" gauges. Yamaha lists the specs as follows: .002"-.004" Intake and .004"-.006" Exhaust, clearance measured when engine is cold.

A set of feeler gauges so you can adjust the valves on your Yamaha. Yamaha says that when the bike is cold, the Intake should be between .002" and .004" and the Exhaust should be between .006" and .007".

This set includes one gauge with a .004" on one end and a .005" on the other for your intake side and another with a .006" and .008" for the exhaust side.

32-Blade Dual-Reading Tapered Combination Feeler Gauge Set

• 95mm (3.75") long taper blades hardened and polished
• Manufacturer's lifetime warranty
• Dual marked: 0.03-1.00mm and .0012-.040 in.

Universal 3 bolt flywheel puller.

Complete with hardware kit and adapter for male or female removal.

• A quick, simple, no mess solution to oil changes
• CNC'd 6061 T-6 aluminum adaptor body
• Knurled grip and Buna O-ring for tool free sealing
• High-temp Silicone hose
• Ergonomic start/stop clamp
• End caps protect threads and provide clean storage
• Engineered, manufactured and assembled in the USA

Two feeler gauges on a single tool. Angled to make checking the clearances easier.

Stock valve clearances are .004" intake and .005" exhaust (.10mm int. and .13mm exh.)

Your automatic cam chain tensioner is spring loaded. This can make it difficult to install as it wants to extend before you have it bolted into place. This handy tool will back off the cam chain tensioner mechanism and hold it for you. No more awkward 3-handed contortions are required to get the tensioner installed.

• Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
• Knurled knob on adjuster drivers ensure a precise and secure grip
• Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw
• Includes 10mm socket with straight slot adjuster
• Fit motorcycles and ATVs with straight slot screw-type adjusters and 10mm lock nuts

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

• Use with 3/8" drive ratchet or wrench
• Choose the one that fits your spark plug size:  14mm, 16mm, 18mm, or 21mm.

This high quality socket from Motion Pro, is specifically designed to reach into the very small, deep space where the spark plug of the XR hides.

Normal sockets simply won't work in this case.

For easy removal of recessed oil filters.

Conical point screws pierces and grabs the metal end cap of the filter.

reduces potential damage to the engine cases.

NOT for use on re-usable oil filters.