Electrical
The Optimate Cable O-20 is a SAE weatherproof bulkhead/panel mount power source. Main body fits a 1" dia. hole. Overall length of the unit is 12" from top of bulkhead to end of connector. Both connectors are industry standard 2-pin SAE connectors. We also offer an optional stainless steel bracket that you can bolt on wherever you like. This makes a clean installation and you won't have a charging cable hanging loose.
Cable max. rating is 10 Amps. Includes an in-line rubber seal at the connector end and a protective cover at the bulkhead for when you don't have something plugged in. Unit has a 3-year limited warranty.
Don't have an SAE plug attached to your battery? Choose the add on below.
This USB device connects to a battery cable with an SAE connector just like the typical Battery Tender outlet, and allows you to charge your electronic devices. Input is 12 Volts, with an output to the USB port of 2.1A maximum, perfect for your phone or other USB devices.
The standard ring connector is a simple, quick connection with a fused positive ring cable and negative cable that attaches directly to your battery with an industry standard 2-pin, SAE connector.
The weather protected ring connector is a premium quick connect permanent battery lead with weather protected connection system and cable. It features 1/4"/M6 ringlets, 20" L, Industry standard 2-pin, heavy-duty SAE connector, 15A fuse, Cable max rating: 5 Amps, Cable remains flexible at below freezing temperatures; rated for -40°F/-40°C.
- Permanent battery leads with integrated battery status/charge system monitors for 12V lead-acid batteries or lithium batteries
- Monitor charge or confirm if the charging system is working correctly
- SAE charge port with weatherproof sealing cap
- Two automatic modes: battery charge level monitor and charging system test
This bright and compact 6-LED flashlight plugs right into your SAE battery charging socket for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to.
A digital voltmeter that can be mounted almost anywhere, on any bike, thanks to ProCycle's multi-position stainless steel bracket. Keeps you informed on the status of your charging system.
Completely waterproof and comes with connectors, wires and thorough instructions. A "must have" device for riders who use heated riding gear, heated grips, additional lighting, GPS, etc.
Lighting
So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved.
This light does not have the large Cyclops logos shown on one of the images.
- Race Inspired Design
- Hella reflector, made in Germany stamped SAE/E4
- Lightweight Aluminum Frame
- Plug and Play for Bikes with H4 Bulbs.
- Available with optional mounting plate for computer or GPS
- Easily converted to HID if desired, uses an H4 bulb
- For bikes that are not H4 (XR650R), a simple H4 plug available at any auto parts store will allow you to use this light.
- Now the panel on top of the light for mounting speedos/gps's etc is included, (This is a platform, not actual GPS mount.)
Optional 10.0 Lumen LED High/Low Upgrade and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get well over double the brightness with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.
Each 10 watt Solstice Solo produces 900 lumens, which is roughly equal to a 50 watt halogen bulb. These are one of the brightest LED off road lamps on the market. The rugged and compact 2” x 2” square die-cast aluminum housing makes mounting easy. The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with other Solstice Solo pods. Includes stainless steel mounting bracket and waterproof connection. Choose narrow, medium, wide or elliptical light beam pattern. Our favorite is the Elliptical pattern which is wide and flat, putting most of the light where you need it the most.
Sold each.
A game changer in compact auxiliary lights. High output, compact and lightweight!
The New Cyclops Aurora 2 inch lights rated at 4000 lumens for the a set. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!
Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need a led flasher to do that)
Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.
Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications. Unless you have a LED factory headlight in a R1200gs,850Gs or KTM1290 these bikes will require our Raider canbus controller.
Look at these quality features!
- Solid Steel cradle mount. No broken or cracked mounts!
- CNC machined aluminum housings
- Polycarbonate lenses, Break-proof!
- 15 degree beam patterns, a great choice for distance and field of view.
- 19 watts each
- 2000 lumens a piece, 4000 lumens for the set.
- Includes a relayed wire harness
- Input voltage 9-30VDC
- R113, R10 TUV and Emark certified
- IP68 Rated
The little light that can! Don't be fooled by the mini size, big light comes out of this bad boy.
New design for 2021 featuring more durable, positive push button switch, metal handle bar mounts and options to allow this light to work for many applications. Switch, cords, strain reliefs and optics for optimal water resistance, ruggedness and performance.
It uses a go pro type mount with an aluminum platform to mount almost anywhere. Also included is a handle bar mount (mount on center of bars). No plastic parts on the light head.
Choose the optional SS platform to mount the light above the bars per two of the identified photos. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars)
Included is a rubber covered handle bar mounted switch with 2 power level settings 50% and full on.
Combo beam pattern, spot and wide beam in one light.
Compatible with Go Pro mounts, Perfect for modern EFI bikes.
- Includes basic wire harness
- 5000 lumens,
- Spot and flood beam in one light
- 28 watt power draw.
- 2 year warranty, does not include crash damage, bent and or broken wires.
- 4 inches long by 1.350 high
Now a lifetime warrantied LED light set at a budget friendly price.. and Not made in China.
The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.
We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.
These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).
The amber version is a Cree 3 watt emitters (12 watts per light).
This combo beam pattern offers good forward lighting and extremely good conspicuity.
The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.
Specs:
- Canbus compatible, full relayed wire harness included
- 5000 plus lumens for the set
- 28 watt draw per white light, 12 watt draw per amber light
- ISO 67... waterproof
- 5600K (white 33% brighter than Amber)
- Life time warrantied
- Sold as a pair
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
- Heavy Duty Design
- IP69K Rating
- Flood, Spot / Flood, & Spot Lens Included
- Stainless Steel Bracket & Hardware
- 5,000k Light Color – Natural Daylight
- Heavy Duty, black, steel Left & Right mounting brackets to bolt directly to your lower triple clamp.
- Harness with Switch
Kit includes: 2x LED Aux lights with harness and switch, 2x Light mounting brackets and bolts, Switch mounting bracket
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes: 2" x 3" LED light pods. Harness with switch and mounting bracket. Left & Right mounting brackets. 4x lower triple clamp bolts
This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.
These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.
Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.
Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.
The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.
This is for Mount Only. Sold individually.
10 Watt LED lights sold separately.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
- Independently programmable flash speed, flash duration, and pre-delay
- Works for LED or Standard Bulb Tail Lights
- All Solid State design
- Meets or exceeds OEM load rating specifications
- Over 1000 possible flash pattern combinations
- Simple programming setup with your brake lever
- Extremely compact unit size; 20mm x 20mm x 12mm
Remove the bulky stock number plate holder with our slim design- comes with LED number plate light.
- Quick and easy install
- Mounting hardware supplied
- Comes with clear LED tail, brake & number plate light
- No mods required for installation
- Available in polished or black PPA coating.
- Pre drilled to suit Australian licence plate
*Please Note: Brake light does not come with necessary/factory connectors. Some cutting, crimping, soldering of wires may be required for connection.
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.
Features:
- High intensity LEDs with amber lenses
- Intended for use as indicators/turn signals
- E mark approved for use as an indicator light
- 15 LEDs per indicator amplifies your visibility to other traffic
- Enhances safety by imrproving clarity of planned directional changes
- Very efficient performance with low power draw
- Designed for use on the upper surface of Barkbusters Jet handguard plastics
- Compatible with the upper and lower surface of VPS & Storm plastics
What's in the box:
- Barkbusters LED indicators in amber (pair)
- Mounting materials
- Installation instructions
Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack
Recommended to use resistor for proper turn signal flash rate.
Specifications
- Comes with mounting hardware.
- Measures 4" long with base and 1" wide at the lights.
Ultra bright amber LED turnsignals offer nearly the same visibility in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.
Pack of Two
These Sequential Turn Signals are available in a 2 pack or 4 pack flexible stem with 7 LEDs on the front models and 14 LEDs on the rear model.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
- Rear signals function as turn indicators and brake light
- E-marked.
- Front and Rear with Flexible Stem: 92mm x 16mm.
You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
- 10 OHM
- Intended for Barkbusters LED Indicator Lights
- Corrects flash rate of LED signals
- Flash rate: 90 (+/- 30) times per minute
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
- Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
- Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
- To verify proper fitment, compare connector photos to OEM connector
- Sold in pairs
Fits Most Models
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Frame
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
- Unique, innovative design
- Wide flat platform
- Openings allow mud/dirt to pass through
- Easy and quick to get on/off
- Good grip
- Reduced vibration
- Extra comfort
Important to verify which style Pivot Pegz you have before ordering.
New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.
- Ceracote coated Chromoly steel pivot for the ultimate in strength
- Replaceable 7075 T6 Aluminum Platform
- Permanent Stainless Teeth provide the ultimate in non-slip traction
- Built-in bottle opener in the bottom!
NOTE: These pegs DO NOT fit the '18 model!
Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
- Mega wide 60mm platform
- Widest and lightest pivoting pegs on the market
- Open design = less mud packing
- Unique multi-directional grip pattern
- Outstanding build quality
- Race proven design and durability
- Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
- Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
- Works on all tapered bearing races from 47 mm to 55 mm OD
- Precision machined anodized aluminum cup will not damage seal surface
- Brass bearing washers for easy use and long life
- Hardened steel jaws engage securely on inner bearing lip
- Lifetime limited warranty
Drivetrain
B&B Heavy-Duty Front Sprocket Case Saver.
The 6mm aluminum base will protect your engine cases should your chain ever break. On top of that is a 4mm thick custom carved plate to keep your pants and other things out of the chain as well. Works with both the 14 and 15 tooth sprockets. A great investment.
- Accurately and quickly measures chain slack
- Two scales measure both chain slack and chain to swingarm clearance
- Setting chain slack properly dramatically improves chain life
- Lightweight compact design fits easily in your tool box or road kit
- Works on most street and dirt bike applications up to 75mm chain slack
- Made from engineered nylon with aluminum measuring scale
- Anodized laser-etched precision measuring scale
- Refer to your owner's manual for proper chain slack and procedure
- Patent pending
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
This brush has 2.25 coils of 360° chemical-resistant nylon bristles to make it the fastest, most effective, precise and systematic method for giving your chain a thorough cleaning. It will help the performance and life of the chain, sprockets, and the engine. This brush will fit any 400 or 500 series chains.
- PBR = press, break, rivet
- Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
- Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
- Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
- Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
- All components conveniently store on tool when not in use
- All steel construction with heat-treated components for strength and durability
- May be supported in a vise or held with included handle
- Great for the professional technician or DIY mechanic
- Compact and light enough to carry in a tool bag for trail-side repairs
- Patent Pending
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
ULTIMATE SPROCKET WRENCH KIT
- 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
- Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
- Dog leg wrench design allows wrench to easily clear rim edge and wide tires
- 8mm allen fits most Japanese bikes 8” long for extra leverage
- Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
- Vinyl coated handles to protect rim edge and give a non slip grip
- Makes routine sprocket bolt maintenance a quick and easy job
Brakes
This will give you a complete SET (Front and Rear) of brake pads.
Sintered Pads are best for regular riding -long life, and good performance in all conditions.
Sport Carbon pads are made for fast riding in dry conditions - not recommended for mud, water, or sand.
Race Sintered are designed for racing use.
Includes front and rear brake pads.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Combines wrench and bleeder valve into one convenient and compact tool
- Fits most 8 mm bleeder nipples
- Bleeds brake systems and hydraulic clutch systems
- Internal check valve for fast easy bleeding
- Anodized billet aluminum handle with chrome moly steel body
- Compact size for tight spaces
- High quality internal seal
- Multi position handle
Suspension
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
Rider Weight w/gear lbs. | Spring Rate |
---|---|
90 or less | .42 |
90-119 | .44 (stock) |
120-150 | .46 |
150-180 | .48 |
180-220 | .50 |
220-250 | .52 |
250+ | .54 |
Emulators make damping rod forks perform like well-tuned cartridge forks. Emulators are tunable valves that sit inside your forks on top of the damping rods and are held in place by the fork springs. Simple to install and completely tunable for all conditions and rider preferences.
An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.
Choose black, blue, red or yellow.
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
Rider Weight w/gear lbs. | Spring Rate |
---|---|
100 or less | 4.6 |
100-124 | 4.8 |
125-149 | 5.0 |
150-174 | 5.2 |
175-199 | 5.4 |
200-224 | 5.7 |
225-274 | 6.0 |
275 + | 6.3 |
The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
- Bolt-on shock valving for riders serious about suspension performance
- Improves control, traction, plushness and bottoming resistance
- Improved, long-wearing, low-friction sealing design decreases fade
- Includes complete instructions
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
- Complete assembly, ready to install into the shock body
- Has air bleed holes to help remove air from the oil reservoir during installation
- Double-lip oil seal design keeps out dirt and keeps friction low
- Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: Thede explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
Makes installation of your linkage bearings much easier. Also simplifies maintenance of those bearings.
- Allows placing bearing needles on bearing race while greasing linkage bearings