Tools and Equipment Click on pic for
larger image
Cost Enter
Qty
Motion Pro 2-Stroke Leak Down Tester
Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines. Packed in a convenient carrying case with instructions.
$312.95
Motion Pro 4-Stroke Leak Down Tester
Designed to check the amount of cylinder leakage in a 4-stroke engines. With an air source of 70 to 160 PSI, this system will pressurize the cylinder with 60 PSI of air. Gauge registers the total percentage of leakage past the rings, head gasket, intake and exhaust valves. System includes 10, 12 & 14mm spark plug adapters, regulator & gauge. This tester will speed up troubleshooting and will help to isolate bad components.
$159.95
Motion Pro Nitrogen Shock Gauge and Filler
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
$228.95
Motion Pro Clutch Holding Tool
Made from medium carbon steel with hardened jaws. It feature spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc.
$25.95
Helix Safety Wire Kit
This package includes safety wire pliers and a 25' roll of .032" stainless steel safety wire.
$38.95
Chain Breaker Tool
Here is a tool to help you remove a few links from a chain that is too long to fit your bike. A great tool to have in your tool box.

! Note! The head of the pivot pin you are going to remove must be ground or filed down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

$16.95
Master Link Pliers
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
$19.95
Motion Pro Chain Alignment Tool
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment.
$18.95
BikeMaster Tire Bead Breaker
Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.
$29.95
Fork Oil Level Gauge
Having the proper fork oil level is imperative to the handling of your bike. Setting the correct fork oil level is a snap with this fully adjustable gauge. The adjustable aluminum level plate can be set from 0 to 295mm. The oil reservoir has single milliliter markings up to 60ml.

Being able to accurately tune your forks by adjusting the oil level can make them better resist brake dive or bottoming. Oil level should be thought of as a fine tuning method to make your choice of spring rate work perfectly for your bike.

$19.95
Race Tech Fork Oil Level Tool
Thanks to Race Tech, you can have the ultimate tool for maintaining your fork oil level. This Fork Oil Level Tool will enable more efficient and accurate fork oil adjustments for pit or shop use. It just can't get any easier than this.
$124.95
Blind Bearing Remover Set
This Motion Pro tool pulls bearing out of those blind holes in engine cases etc. Set includes 30, 25, 20, 17, 15, 12, 10 and 8mm collets. 2 pound slide hammer. Crossbar type shaft allows easy collet removal. Necessary tool for most transmission rebuilds. Can be used for wheel bearing removal.
$277.95
Crank Case Separator Tool Set
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
$79.95
Motion Pro Steering Head Race Puller
New from Motion Pro is a way to remove your steering bearings without damaging them. Remove all tapered bearing races from 47mm to 52mm OD. Tool uses a precision machined anodized aluminum cup that will not damage the seal surface while hardened steel jaws securely engage the inner lip and pulls the race out perfectly straight causing no damage to the race or frame. Motion Pro includes a limited lifetime warranty on this tool.
$59.95
Motion Pro 43mm Fork Seal Driver
New from Motion Pro is a way to remove your steering bearings without damaging them. Remove all tapered bearing races from 47mm to 52mm OD. Tool uses a precision machined anodized aluminum cup that will not damage the seal surface while hardened steel jaws securely engage the inner lip and pulls the race out perfectly straight causing no damage to the race or frame. Motion Pro includes a limited lifetime warranty on this tool.
$44.95
New! 042117 Magura Clutch Bleed Kit
Hydraulic Clutch Bleeder Kit includes 2oz of Magura Blood clutch fluid, 2 bleeder tools and fittings to properly bleed your hydraulic clutch. Great if you have air infiltration in the system or damaged it in some fashion.
$27.95
Didn't find what you are looking for?
We have millions of parts and accessories not listed on our site available from our vendors.