Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
Supermoto version of the DRZ400S
Street legal. Electric start. Wide 17" wheels.
Sold in the US 2000-current
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
| 520x110 | 15T | 41T | 120/70-17 | 140/70-17 | CR8E |
Replace the wimpy stock DRZ400 Skid Plate made from 4mm thick 5083 aluminium plate. Strong and great looking. Leave the stock wings in place and give yourself something that will really stop any damage between the frame rails. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.
The B & B Eng. DRZ400 Bash Plate is made from 4mm thick 5083 aluminium plate. Strong and great looking, this is the top of the line protection plate for the DRZ. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.
The use of Kevlar gives this composite a longer fatigue life and greater tensile strength than aluminum. Composite plates will bounce back from hard hits and look great long after aluminum plates give up.
Clutch and Ignition covers made by B&B Eng. Formed from 2mm thick 5052 aluminum plate, selected because of its strength, corrosion resistance, excellent abrasion and impact protection. These will help protect your cases in the event of a bad fall.
These covers are attached to the engine cases with high quality heat resistance silicone adhesive
These covers will NOT fit early kick start only models that did not come standard with electric start. If you have added a kick starter to your bike that came with an electric start, covers will fit with no problem.
Protect your frame/paint from scuffs and scratches with frame guards. The DRZ 400 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
Give your DRZ that factory prepped look and protect your frame.
These frame guards from industry leaders Works Connection are CNC cut and formed from aircraft grade 5052 aluminum. These not only protect your frame from scuff and rub marks from your boots, but also give you a flatter surface for better grip and control with your lower legs. All the necessary mounting hardware is included making these a very simple bolt-on installation.
High quality aluminum caliper guards from Works Connection protects your brake caliper and looks great too.
Radiator guards from Devol Racing protect your radiators from damage due to trail side objects and roost bullets. They offer protection not just from frontal assaults but also from those tricky side attacks. Made from high-grade aluminum alloy for light weight and strength, these guards have an improved air-flow design that eliminates any overheating problem. A solid mounting to the frame make these stronger than most guards that just mount to the radiators themselves.
Devol Racing makes a super product that will keep you on the trail for a long time.
CNC machined from 2.5mm marine grade aluminum- replace the stock plastic guard
Don't cut the ball ends off of your levers! These billet spacers move your hand guards outward to allow clearance for the full length of the stock levers. Designed to fit steel or aluminum bars. Includes longer stainless steel mounting bolts.
Developed for the DR650 but may work on other models with long levers. (May require additional adjustment or modification on some models.)
Not compatible with Acerbis and Emgo hand guards
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Images show a set of these hand guards installed on a set of CR High Gunmetal Fly Handlebars with large black deflectors. The far right image shows the need to flip the brackets that attach to the bar on the clutch and front brake side. On the front brake side the clamp must go over the front brake line while on the clutch side it goes under the cable.
Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Some models with adjustable windscreens may need the windscreen rotated forward, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.
These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.
Works with 7/8" or 1-1/8" bars.
X-Factor guards may require you to cut your lever ends down, or use short levers.
Replacement handguards for your Acerbis set up. Tough Polypropylene shields with a larger 6" outer diameter, built for extreme riding conditions.
The X-Factory Handguards from Acerbis feature a steel bar wrapped with an injection molded Nylon composite. A replaceable dual injected polypropylene shield mounts to the bar offering insurmountable protection from roost, debris, and extreme conditions.
A universal mount kit is included that allows for mounting on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
Weight:
360 grams/pair or
180 grams/each
Fitment Notes: If you have a hardware kit listed below see special fitting notes as additional parts may be required
BHG-010 Requires two additional M6x40mm countersunk bolts
BHG-032 R1200GS/A requires two additional M8x55mm countersunk bolts
BHG-045 G650GS requires two additional M6x65mm countersunk bolts
BHG-050 Will not fit
BHG-051 Requires two additional M6x50mm countersunk bolts
BHG-059 Tiger XC, XCA & XCX (all ’15 on) use M6x45mm bolt from BHG-059 kit
BHG-075 Will not fit
BHG-079 Will not fit
Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters 1-1/8 inch (28.5mm) handlebar saddle clamp set.
What's in the box:
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
Maximize your wind protection with the Barkbusters largest handguard plastic! For use with single sided Storm mount and all Barkbusters backbone handguards
Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
Replace the deflectors on your aluminum bar backbones with Barkbusters VPS wind protection replacement handguards.
Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.
Select your desired color.
Must add the corresponding size mounts to fit your handlebar.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Please Note: These handguards do not fit the Yamaha T7
You can keep your Cycra handguards even if you upgrade your handlebars to a different width.
Replacement mounts that keep your Cycra handguards fresh and tight.
CNC-machined from billet aluminum for the best fit and strength.
Please Note: These handguards do not fit the Yamaha T7
Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.
Fits Moose and other aluminum hand guards
FUZION guard feature the ultimate in hand protection with a unique design and flexible yet durable material.
The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions.
The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable.
The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence.
Kit includes mounts. Optional replacement mounts available.
Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.
Features:
Whats in the box:
The OBR ADV Gear Enduro ¾ Grip Mitt is your answer to cold fingers! Our ¾ open design terminates right at the wrist, but still offers full coverage of the hand while blocking the swirling air flow that freezes finger tips. Their ¾ open design does not cover important controls such as Hi/Lo Beam, Turn Indicator, or Kill Switches making this Grip Mitt perfect for both Off Road, Enduro, ADV, and ATV applications with full wrap hand guards.
Features
Droppin’ into the weather? Combine Bushwackers Hand Guards with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Essential gear for motorcycles, snow bikes and snowmobiles.
REQUIRED EQUIPMENT: Motorcycle must be equipped with rigid hand guards or deflectors to support Bushwackers while riding.
Materials: Corona (UV) Treated, Matte Finish, .055 Gauge Polyethylene Plastic
Dimensions (flat): 13.5″ (length from end closest to bar clamp to end closest to bar end) x 16″ (widest part at end of bars) x 6″ (narrowest part nearest center of bar)
It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.
Sold in pairs.
Hand/brush guards are required for proper fitment and for safety reasons.
Hippo Hands go on and off in seconds and never require tools or hardware.
The Backcountry is 9" deep.
If you like to stand and ride, this is the model for you! But… these hand covers also fit to just about any bike. They are also a great option for cruisers with hand guards or lever guards.
They feature a durable, quilted interior and flexible, neoprene cuff which ensures a great fit on so many bikes. The Backcountry is their smallest, most easily adaptable hand cover.
The Backcountry features a front reflective panel for higher visibility in low light situations.
Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.
The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.
