This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Call or Text
+1-541-688-9543Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
Important to verify which style Pivot Pegz you have before ordering.
New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.
NOTE: These pegs DO NOT fit the '18 model!
Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
B&B Heavy-Duty Front Sprocket Case Saver.
The 6mm aluminum base will protect your engine cases should your chain ever break. On top of that is a 4mm thick custom carved plate to keep your pants and other things out of the chain as well. Works with both the 14 and 15 tooth sprockets. A great investment.
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
ULTIMATE SPROCKET WRENCH KIT
SMX Carbon Look Rotor
This will give you a complete SET (Front and Rear) of brake pads.
Sintered Pads are best for regular riding -long life, and good performance in all conditions.
Sport Carbon pads are made for fast riding in dry conditions - not recommended for mud, water, or sand.
Race Sintered are designed for racing use.
Includes front and rear brake pads.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Steel braided lines have a Teflon tube as a core wrapped with a stainless steel wire braided exterior which doesn't allow the brake lines to stretch under pressure like stock rubber lines do.
The benefit is a firmer brake lever with better feel because the energy that was going into stretching the stock lines now goes straight to the brakes.
Combines wrench and bleeder valve into one convenient and compact tool
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
Rider Weight w/gear lbs. | Spring Rate |
---|---|
90 or less | .42 |
90-119 | .44 (stock) |
120-150 | .46 |
150-180 | .48 |
180-220 | .50 |
220-250 | .52 |
250+ | .54 |
An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.
Choose black, blue, red or yellow.
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
Rider Weight w/gear lbs. | Spring Rate |
---|---|
100 or less | 4.6 |
100-124 | 4.8 |
125-149 | 5.0 |
150-174 | 5.2 |
175-199 | 5.4 |
200-224 | 5.7 |
225-274 | 6.0 |
275 + | 6.3 |
The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: Thede explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
Makes installation of your linkage bearings much easier. Also simplifies maintenance of those bearings.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.
All handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The race-bred RS-2 exhaust has proven to be extremely popular among rider looks for a combination of performance and value. It enhances performance dramatically, provides an enviable exhaust note and offers the unmistakable look and sound of Yoshimura. RS-2 mufflers feature a straight baffle that leads to a single turn-down machined aluminum end cap.
All models have a USFS Approved spark arrester in a oval-shaped sleeve with a large volume of packing material.
The RS-4 Twin Pipe kit was previously only available as a custom system for Kevin Schwantz.
Yoshimura is offering these incredible "Twice Pipes" which are completely fabricated by hand and TIG welded to perfection. They certainly sit at the high end of what is available for the mighty SM... The pipes have a stainless steel header and "Y" pipe mated to twin carbon fiber or aluminum RS-4 mufflers for incredible looks and performance. The kit also comes with a custom Yoshimura side stand.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Unit is pounds lighter than stock and gives gains in horsepower and torque throughout the RPM range. All of that in a package handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The V2 Series Slip-On muffler features an aluminum body, TIG welded components, stainless steel inlet tube and a great new look. This Lightweight Slip-On weighs approximately 5.5 lbs.
The DG Performance systems offer increased throttle response, power and torque. Standard sound level is approximately 98 db. Equipped with a US Forestry approved spark arrestor.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available.
Constructed from aircraft grade aluminum and high strength stainless steel.
Sound output 96dB. Several pounds lighter than the stock muffler.
No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.
This muffler works on OEM header only!
Yoshimura RS-3 that will slip right on to your stock header. Made by hand to the highest quality standards using the championship-winning racetrack experience and their extensive R&D facility ensure these pipes perform and will last.
Both full systems and slip-on mufflers include 96 dB sound insert/USFS approved spark arrestor installed in the muffler. Mid-pipe is stainless steel while the stainless RS-3 oval muffler design has a slim profile with an aluminum end cap.
Works on OEM header only!
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.
Their baffle was designed to replace the stock insert. The baffle produces a nice note compared to the de-restricted stock version and dyno test results showed an increase on 2 hp up top.
A noise test on the insert was conducted at the EPA Victoria Vehicle Test Station at Macleod under controlled conditions with Class 1 meters.
Tested Bike | ADR Signature dB(A) & test RPM | ADR tess with B&B Tip |
---|---|---|
Suzuki DRZ 400 | 93 dB(A) @ 3375 RPM | 97 dB(A) @ 3375 RPM |
Some extra details:
Does not contain a spark arrestor. Check local laws on spark arrestors before purchase.
This Quiet Insert comes stock in all new FMF Q4 mufflers. If you lost yours, this is the replacement you need.
It will fit Q4, Q4 Hex, Powercore and Powercore Hex mufflers.
It will reduce the sound rating of the Power Core models, from about 99db down to about 96db.
Please choose the correct Insert for your muffler. If you are unsure of the year that your muffler was manufactured you can easily identify visually which insert you will need.
Pre '21 | Installs using one small screw |
'21-Cur | Installs using a spiral retaining ring |
The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.
If your aftermarket exhaust is missing heat shield mounting points for this is the easy fix you’ve been waiting for. Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.
Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.
The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.
We highly recommend a heat shield if you run soft luggage without hard racks.
FEATURES:
DIMENSIONS:
Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.
The latest in muffler packing technology. Spec 31 high performance muffler packing resists breakdown up to 1400°F, is universal, and is easy to install.
A highly refined blend of aluminum, copper and graphite lubricants. Use during assembly to prevent galling, corrosion and seizing due to weathering or chemicals. Anti-Seize assures easier disassembly. Temperature range: -60°F to 1600°F (-50°C to 870°C). Salt, corrosion and moisture resistant – ideal for marine use. Meets Mil Spec #907E.
Replacement Exhaust Pipe Retention Spring