XR650L: Drivetrain

High Quality chain. Will need to be cut to fit your sprocket combination.

Always carry a spare master link when out on the trail.

  Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.

These do not fit the TW200 or XT250. Only for 520 os 525 chains, Please verify chain size.

Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.

This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).

This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.

Designed for OFF ROAD USE with the thought in mind that you can ride to your favorite off road spot using a 15 or 16 tooth sprocket and larger than stock rear sprocket. Then quickly change to the 13 tooth and enjoy the ripping torque provided by the huge amount of reduction the 13 tooth offers. Making the XRL much better in the technical stuff. You will really be surprised how much better a big bike like an XRL handles off road with low gearing.

This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.

Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.

A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.

A 16 TOOTH SPROCKET IS THE BIGGEST FRONT SPROCKET THAT WILL RUN WITH THE STANDARD 110 LINK CHAIN AND 45 TOOTH REAR SPROCKET ON A XR650L* THE OEM COVER WILL REQUIRE MODIFYING TO USE THE 16 TOOTH SPROCKET ON YOUR XR650L.

Quality steel rear sprockets.

Color may vary based on manufacturer availability, quality will not be compromised.

This kit will replace your stock sprocket bolts and nuts with new hardware.

Factory Honda replacements in a convenient kit.

Chain sliders and guides tend to wear out over time due to chain friction. Replace worn out components with genuine Honda parts!

• Click on image to enlarge
• Select part
• To add multiple components, add to cart one at a time.

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

• Will not harm O-ring chains
• Easily adjustable for all chain sizes

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).

Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.

Maximum master link width 24.8mm.

Will not damage master links, hardened steel pins for reliable use.

Light weight billet aluminum construction.

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.

Fits 520, 525, and 530 pitch chain.

ULTIMATE SPROCKET WRENCH KIT

• 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
• Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
• Dog leg wrench design allows wrench to easily clear rim edge and wide tires
• 8mm allen fits most Japanese bikes 8” long for extra leverage
• Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
• Vinyl coated handles to protect rim edge and give a non slip grip
• Makes routine sprocket bolt maintenance a quick and easy job