Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
Headlights, Taillights, Turn Signals, etc.
Basic Lighting Tech Talk: https://youtu.be/B_ums5wHN1Y
LED Bulbs Tech Talk: https://youtu.be/gAqlsO-5GyI
Model
Made In
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
- 10 OHM
- Intended for Barkbusters LED Indicator Lights
- Corrects flash rate of LED signals
- Flash rate: 90 (+/- 30) times per minute
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
- Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
- Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
- To verify proper fitment, compare connector photos to OEM connector
- Sold in pairs
Fits Most Models
The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.
Features:
- High intensity LEDs with amber lenses
- Intended for use as indicators/turn signals
- E mark approved for use as an indicator light
- 15 LEDs per indicator amplifies your visibility to other traffic
- Enhances safety by imrproving clarity of planned directional changes
- Very efficient performance with low power draw
- Designed for use on the upper surface of Barkbusters Jet handguard plastics
- Compatible with the upper and lower surface of VPS & Storm plastics
What's in the box:
- Barkbusters LED indicators in amber (pair)
- Mounting materials
- Installation instructions
Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack
Recommended to use resistor for proper turn signal flash rate.
Specifications
- Comes with mounting hardware.
- Measures 4" long with base and 1" wide at the lights.
Ultra bright amber LED turnsignals offer nearly the same visibility in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.
Pack of Two
These Sequential Turn Signals are available in a 2 pack or 4 pack flexible stem with 7 LEDs on the front models and 14 LEDs on the rear model.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
- Rear signals function as turn indicators and brake light
- E-marked.
- Front and Rear with Flexible Stem: 92mm x 16mm.